Paper Windows and Mono-Material Cartons: Designing Corrugated Boxes for Recyclability under the PPWR

The PPWR does not define mono-material packaging, but it makes recyclability a condition for all packaging. Under Regulation (EU) 2025/40, all packaging must be recyclable (Article 6(1)), and from 1 January 2030 at the earliest it must reach recyclability grade A, B or C under design-for-recycling criteria that the Commission is due to adopt by 1 January 2028. Annex II prefers mono-materials and lists paper or cardboard with plastic windows as composite packaging. A corrugated box with a paper window or no window, and without film lamination, stays paper only. Status 13 November 2026; general information, not legal advice.

What the PPWR requires on recyclability

Regulation (EU) 2025/40 has applied since 12 August 2026. Dates below are as of 13 November 2026.

Requirement Article When What it means for a carton
All packaging placed on the market shall be recyclable 6(1) From 12 August 2026, according to the Commission’s guidance Until the design-for-recycling criteria apply, the guidance points to the old Packaging Directive and standards such as EN 13430:2004
Design-for-recycling criteria and the method for grading, per packaging category of Annex II, Table 1 6(4) Delegated acts due by 1 January 2028 Corrugated boxes fall under paper/cardboard packaging (category 2); paper or cardboard with plastic windows or plastic laminates is composite packaging (category 3)
Grades A (95% or more), B (80% or more) and C (70% or more); below 70% the packaging is technically non-recyclable 6(3); Annex II, Table 3 Grade C or better from 1 January 2030 or 24 months after the delegated acts, whichever is later; grade A or B from 1 January 2038 The grade is assessed per packaging unit, including integrated components such as a glued-in window
Recycled at scale: separately collected, sorted and recycled, with at least 55% recycled at Union level for materials other than wood 6(2)(b) and (5); 3(1), point 39 From 1 January 2035 or five years after the implementing acts (due by 1 January 2030), whichever is later Assessed per packaging category, not per box
EPR fees modulated by recyclability grade 6(8) 18 months after the delegated and implementing acts enter into force The producer’s fee will depend on the grade (see packaging EPR for online sellers)
Proof in the technical documentation (Annex VII); suppliers provide the information needed 6(9), 15(2) and (3), 16(1) With the recyclability requirements; kept for 5 years for single-use packaging The manufacturer (generally the company that has the packaging made under its own name or trademark) needs a full list of materials from the carton supplier
Harmonised label on material composition 12(1) From 12 August 2028 or 24 months after the implementing acts, whichever is later Applies to e-commerce packaging but not to other transport packaging
Environmental claims on properties regulated by the PPWR 14 From 12 August 2026 Only for properties beyond the minimum requirements, stating whether the claim covers the whole unit or a part

The delegated acts under Article 6(4) and the implementing acts on labels under Article 12(6) and (7), the latter due by 12 August 2026, did not appear in our search of EUR-Lex on 13 November 2026. Until the criteria exist, nobody can state an official grade for a carton. The Commission’s guidance and FAQ are its interpretation; only the Court of Justice interprets EU law bindingly. For the overall timeline see the PPWR checklist for packaging buyers.

What mono-material means for a corrugated carton

The Regulation mentions mono-materials only in its annexes: Annex II, Table 4 says that mono-materials, or material combinations that permit easy separation and a high yield of secondary raw materials, are preferable. The legal line is drawn by the definition of composite packaging in Article 3(1), point 24: a unit made of two or more different materials that cannot be separated by hand, unless one of them is an insignificant part and no more than 5% of the total mass of the unit. Labels, varnishes, paints, inks, adhesives and lacquers are not counted. The Commission’s guidance reads this 5% as the threshold below which packaging is deemed to be a mono-material.

Staying below 5% does not decide the grade. The 4evergreen industry guideline stresses that the 5% threshold is not a recyclability metric, and Article 6(9) requires integrated components to be assessed together with the box: no component may hinder the recyclability of the main body. A component the user has to remove completely is a separate component (Article 3(1), point 44) and is assessed on its own.

For fresh produce there is one more rule: from 1 January 2030, Annex V, point 2 restricts single-use plastic packaging for less than 1.5 kg of pre-packed fresh fruit and vegetables, with exemptions that Member States may set (Article 25(1)). The Commission’s guidance treats paper-based packaging with a plastic share above the 5% threshold as covered by the restrictions in Annex V, points 1 to 4. Weigh a punnet with a film window or plastic liner component by component.

Design choices compared

The table compares the Regulation with two industry guidelines, 4evergreen (version 4, February 2026) and FEFCO (2025). The guidelines are not law, and the official criteria may differ.

Element PPWR Industry guidelines Mono-material option
Plastic film window, glued in Annex II, Table 1, category 3; an integrated component assessed with the box 4evergreen: avoid strongly attached windows, consider thin, lightweight, easily detachable ones; FEFCO: integrated plastic windows have conditional compatibility Paper window, a printed image of the product, or no window
Film lamination Plastic-laminated paper/cardboard is category 3; a film counts towards the 5% FEFCO: uncoated and unlaminated board is preferable, a one-side plastic laminate is acceptable only under conditions, a two-side laminate has low compatibility Print on the liner or laminate a printed paper sheet (see litho-laminated boxes)
Inks and varnish Not counted in the 5%; a parameter in Annex II, Table 4 FEFCO: water-soluble inks and varnishes are preferred; keep cured varnish, conventional or UV, to a minimum Print without a full-surface varnish (see printing on corrugated boxes)
Adhesives for windows and seams Not counted in the 5%; a parameter in Annex II, Table 4 FEFCO rates starch-based and PVA adhesives as fully compatible; both guidelines treat hotmelts with a softening point below 68 °C (DIN EN 1427) as a problem Agree the adhesive at the design stage
Wax and barrier coatings A parameter in Annex II, Table 4 FEFCO: avoid wax and waxed papers in a standard mill Check wax-free options (see wax-free moisture-resistant boxes)

Paper window, cut-out or film: how to choose

  • Paper window. A translucent paper such as glassine keeps the box paper only, but the product shows less sharply than through film: judge it on a sample. Greasy or moist products need a trial.
  • No window. A printed image of the product, or a printed insert, is the simplest mono-material solution.
  • Open cut-out. No window material, but the product is exposed to dust, and any opening removes board from a panel: check the stacking strength (see ECT, BCT and the McKee formula).
  • Removable film window. Where film cannot be replaced, 4evergreen recommends detachable, thin and lightweight solutions with clear disposal instructions on the pack.
  • Glued-in film window. Still possible where full clarity or water resistance is needed, but it counts in the assessment of the whole unit.

How recyclability is tested today

The legal method will come with the delegated acts under Article 6(4)(b). Until then the paper industry uses laboratory tests that simulate a paper mill, mainly the Cepi recyclability laboratory test method for mills with a conventional process (version 3, February 2025). 4evergreen pairs it with its own evaluation protocol, also accepts positive results obtained until 2030 with older methods such as Aticelca MC501:2019, and notes that there is no harmonised EU-wide method for calculating recyclability under the PPWR yet. A result applies to the tested design only, so test the exact design if you plan any claim on the box.

Claims and labels: say what the box is made of

Article 6(1) already makes recyclability a minimum requirement for all packaging, and Article 14 allows environmental claims about such properties only where they go beyond the minimum and state whether they cover the whole unit or a part of it. The Commission’s FAQ places recyclability claims under Article 14; claims outside the PPWR fall under the consumer rules of Directive (EU) 2024/825. Article 12(8) also bars misleading labels. A factual statement is safer: a carton made only of board can be put in the paper collection container. Check other wording with your adviser.

Checklist: what to ask your carton supplier

  1. Bill of materials. Every component (board, window, film, coating, adhesive, tape, insert) with its weight and its share of the total mass of the unit.
  2. Function. Which film, laminate, varnish or coating is really needed, and what is the paper-only alternative?
  3. Window. Material, size, how it is fixed, adhesive type and softening point, and whether the user can remove it.
  4. Print. Ink system (water-based, UV), varnish type and coverage.
  5. Board data. Recycled or virgin fibre, and the board makers’ environmental data for your reporting.
  6. Tests. A laboratory recyclability test of the exact design (method, laboratory, date) and, if you cut a window, a compression test.
  7. Documentation. Information for your technical documentation (Article 16(1)) and, for food, the declaration of conformity.
  8. Wording. What the box will say about material and disposal, and who has checked it against Article 14.

What we can do

We can make or source cartons with a paper window instead of film and cartons without film lamination or varnish, made to order; we select and trial the variant with you. Where the product needs them, we also make film-laminated and varnished boxes. We print in flexo or digitally, including UV, and have board with a declaration of conformity for direct food contact. We can help review a box under the PPWR (materials, empty space), supply environmental data on the board from our suppliers and arrange package tests (compression, drop, transport simulation) in a partner laboratory; terms are agreed individually. We do not state a recyclability grade in advance. We tailor order quantities to your needs – we also make short runs and prototypes. If a construction requires a minimum quantity, we state it in the quote.

Sources

Regulation (EU) 2025/40 on EUR-Lex (Articles 3, 6, 12, 14 to 16 and 25, Annexes II, V and VII); Commission guidance document for the PPWR (10 June 2026); Commission FAQ on the PPWR (3 August 2026); 4evergreen Circularity by Design Guideline (version 4, February 2026); FEFCO Corrugated Packaging Recyclability Guidelines (2025); Cepi recyclability laboratory test method (version 3, February 2025). Check the current texts before you decide: the delegated acts on design for recycling had not appeared in EUR-Lex on 13 November 2026.

What to send us

Tell us the product, whether it must be visible, any food or moisture requirements and the dimensions. We produce boxes to your dimensions. Send your enquiry through our home page.

Frequently asked questions

Does the PPWR define mono-material packaging?

No. Regulation (EU) 2025/40 has no definition of mono-material. It defines composite packaging instead: materials that cannot be separated by hand, unless one is no more than 5% of the total mass, not counting labels, varnishes, paints, inks, adhesives and lacquers (Article 3(1), point 24). Annex II, Table 4 prefers mono-materials or easily separable combinations.

Is a corrugated box with a plastic window still allowed?

Yes, the PPWR does not ban windows as such. Annex II, Table 1 lists paper with plastic windows as composite packaging, and from 1 January 2030 at the earliest the box must reach grade A, B or C under criteria not yet published on 13 November 2026. For less than 1.5 kg of fresh fruit and vegetables, also check Annex V, point 2.

When do the recyclability grades A, B and C apply?

From 1 January 2030 or 24 months after the delegated acts with the design-for-recycling criteria enter into force, whichever is later (Article 6(3)). The Commission is due to adopt those acts by 1 January 2028. From 1 January 2038 only grades A and B are allowed. In the assessment per packaging unit, grade A means 95% or more, B 80% or more and C 70% or more (Annex II, Table 3).

Do varnish, ink and glue count towards the 5% threshold?

Not for the definition of composite packaging. They still matter for the grade: Annex II, Table 4 lists adhesives, inks and lacquers, barriers and coatings among the parameters for the design-for-recycling criteria.

Is a paper window as clear as a film window?

No. A paper window, for example glassine, is translucent rather than clear. Judge it on a sample with your product, and test greasy or moist products first.

Can my box say that it is recyclable?

Check with your adviser first. Article 14 allows claims about properties regulated by the PPWR only beyond the minimum requirements and with a statement of whether they cover the whole unit or a part, and the Commission’s FAQ places recyclability claims under it. Stating the material is safer.

Can you tell me the recyclability grade of my box now?

No. The method for assessing and expressing the grade will be set in the delegated acts under Article 6(4), which had not been published in EUR-Lex as of 13 November 2026. A laboratory test to an industry method shows how one design behaves, but it is not a legal grade.

Can you make cartons with a paper window or without film?

Yes, made to order: we can make or source cartons with a paper window instead of film and cartons without film lamination or varnish, and we trial the variant with you. We do not promise a recyclability grade in advance.