Printing on Corrugated Boxes: Flexo vs Digital, Water-Based vs UV Varnish, Variable Data and QR Codes

Flexography and digital inkjet are the two main ways to print directly on corrugated boxes. Flexo transfers ink from a relief plate, one plate per colour, and suits long runs with fixed artwork in a few colours. Digital printing works straight from files without plates and can print different data on every box, so it fits short and medium runs, many versions, serial numbers and QR codes. Water-based varnish is the standard protective coat; UV varnish usually gives a higher gloss. As of 13 November 2026; no prices.

Flexo or digital: how the two methods compare

Both methods print on the finished board (post-print). A third route, pre-print, prints the liner before the board is corrugated; litho-lamination glues a printed paper sheet onto the board (see litho-laminated corrugated boxes).

Criterion Flexo post-print Digital inkjet (pigment or UV)
How it prints A flexible relief plate (usually photopolymer) carries water-based ink to the board Print heads jet ink directly onto the board, controlled from the file
Tooling One plate per colour and per design, a one-off cost spread over the run No plates; artwork can change from one box to the next
Colours and graphics Logos, text and simple graphics; at Kartoniki.eu up to 4 colours Multicolour and photographic artwork from CMYK
Variable data No: the image is the same on every box Yes: serial numbers, QR and DataMatrix codes, names, language versions
Typical run Long runs with fixed artwork Short and medium runs, many versions, prototypes

The break-even point depends on the number of versions, the board and the quantity, so there is no single number (see one-off costs for custom boxes). One design can also combine both: flexo for the brand colours, digital for the codes.

Does printing weaken the box?

Flexo plates press on the board, and that pressure can partly crush the flutes. In a laboratory study by Andrzejak and Garbowski (Przegląd Papierniczy, November 2021) on single-wall E, B and C boards printed over the full surface:

  • flexo printing lowered edge crush resistance (ECT) by 2.0 to 12.6% compared with unprinted board;
  • the calculated box compression strength (BCT) of flexo-printed boxes was 5 to 11% lower;
  • UV-cured digital printing did not lower these values; ECT was 0.6 to 2.4% higher and BCT at most about 3% higher.

This is one study with specific boards and full coverage, not a rule for every job. Earlier theses from Rochester Institute of Technology also found that plate type, impression and number of colours in flexo affected compression strength, while thin plates with a compressible backing largely avoided the loss. For stacked or heavy loads, include the print in the board choice and test the printed box (see ECT, BCT and the McKee formula).

Colour: CMYK, Pantone and the board underneath

  • The board changes the colour. On brown kraft liners colours look darker and less saturated than on a white liner; a white liner or a white underprint gives more contrast.
  • Spot colours or CMYK. Flexo prints spot colours mixed to a reference such as a Pantone shade. Digital printing builds colours from CMYK, and Pantone itself shows only the nearest CMYK match for each spot colour: some deep blues, bright greens and oranges fall outside the CMYK gamut.
  • Proof on the real board. A screen or a proof on coated paper does not show the result on corrugated board. Approve a printed sample on the production board and keep it as the reference for repeat orders.
  • Metallic effects. Gold and silver need special metallic inks or a foil; CMYK cannot simulate them.
  • Fine detail. Avoid very thin lines and very small text on the uneven corrugated surface, and keep important elements away from creases.

Varnishes and coatings

Finish How it forms Look Typical use
Water-based (dispersion) varnish Dries as the water evaporates or is absorbed Gloss, satin or matt Standard protection of print on shipping boxes
UV varnish Cured by UV light Usually higher gloss; matt also possible Gift packs, displays, spot effects on a logo
Spot varnish Applied only to marked areas Gloss or matt contrast, for example on a logo Premium packaging; needs a separate varnish layer in the file
Film lamination A thin film is applied to the printed surface Gloss, matt, soft touch, metallic Premium packs where the surface must stay clean

Varnish and film protect the print against abrasion and dirt, but they do not make a box waterproof: describe moisture or cold-chain conditions in your enquiry. Glue flaps and adhesive strips are normally left free of varnish, because glue bonds less well on a coated surface. Abrasion resistance depends on the ink, the varnish and the board; for long routes or frequent handling, ask for a rub test or a transport trial. A box made only of board goes into the paper collection container; a film needs a separate check before you make any claim about the pack.

Printing on food packaging

Food contact materials must not transfer their constituents to food in quantities that could endanger health or change the food (Article 3 of Regulation (EC) No 1935/2004). For printing inks on the non-food-contact side, the Annex to Regulation (EC) No 2023/2006 requires that substances do not pass to the food side through the board or by set-off in the stack, and that printed surfaces do not touch food directly. Printing inks are not among the materials with specific EU measures; with UV inks and varnishes, residues of unreacted photoinitiators can migrate into food, which is why low-migration systems exist. In your enquiry, state whether contact is direct and what food it is, and ask for a declaration of compliance for the board and the coating. Sector details are in corrugated boxes for pizza, takeaway and bakery. General information, not legal advice.

Variable data, QR codes and DataMatrix

Variable data printing combines fixed artwork with a data file (CSV or XML) in which each line is one box: a serial number, a code, a batch, a name or a language version. Only digital printing can do this. Which code to use depends on who reads it.

Code What it carries Read by Typical use on a box
QR code (optionally with a GS1 Digital Link URI) A web address; with GS1 Digital Link also a GTIN, batch or serial number Smartphones and 2D scanners Product information, instructions, returns, tracking of reusable cartons
GS1 DataMatrix GTIN plus data such as expiry date or serial number in a compact square 2D scanners Logistics and traceability, widely used in healthcare
ITF-14 The GTIN of the case only Linear scanners Cases and logistic units; robust enough to print directly on corrugated board

For a code that scans reliably on corrugated board:

  1. Contrast. Dark code on a light background; black on white is ideal. On brown board, a code on a white liner or on a label reads more reliably. Avoid red codes: scanners using red light may not see them.
  2. Quiet zone. At least 4 modules of clear margin around a QR code and 1 module around a DataMatrix; more next to other print.
  3. Position. A flat panel, away from creases, flap edges, tape and stretch film.
  4. Size. Larger modules tolerate ink spread on rough board better; agree the size with whoever scans the boxes.
  5. Verification. Test-scan samples on the production board with your own scanners; if a grade is required, verify 2D codes to ISO/IEC 15415 and linear barcodes to ISO/IEC 15416.

Under the PPWR (Regulation (EU) 2025/40, Article 12(1)), a harmonised label on material composition applies from 12 August 2028 or 24 months after the implementing acts, whichever is later. Transport packaging is exempt, but e-commerce packaging is not, and a QR code with sorting information may be added. Labels and codes must be printed visibly, legibly and so that they cannot be easily erased (Article 12(5)). Reusable packaging has its own label and QR rules (Article 12(2)); see returnable and reusable shipping cartons under the PPWR. Status 13 November 2026; general information, not legal advice.

Preparing your artwork

  1. Format. PDF with logos and text as vectors; name the colours (CMYK or Pantone).
  2. Die line. We prepare it for your size; artwork placed on it keeps print off creases and glue flaps.
  3. Panels and colours. Say which panels are printed, outside or inside, and whether one colour is enough: in flexo each colour is a separate plate.
  4. Layers. Spot varnish needs its own layer.
  5. Variable data. A data file with one line per box, the code type and size, and whether codes must be verified.

No artwork? We can prepare a design or reproduce the print from a box you send us; terms are in the quote.

Checklist: what to agree with your supplier

  1. Which method (flexo, digital or both) suits your run length and number of versions.
  2. On which board and liner (brown or white) colours will be judged, and which printed sample is the colour reference.
  3. Whether the print could reduce box strength for your load, and whether the printed box will be tested.
  4. Which varnish, where, and which areas stay free for gluing.
  5. For food: direct or indirect contact, and the declaration of compliance for board and coating.
  6. For codes: type, size, quiet zone, position, scanner type and verification method.
  7. Which one-off costs apply (plates, die, design, samples) and whether they recur on repeat orders.

What we can do

We print flexographically in up to 4 colours and digitally in pigment and UV technology, including variable data such as serial numbers, QR and DataMatrix codes. We match colours to Pantone, can print the full surface of a box in one colour, apply gold and silver foil, and varnish the full surface or selected areas with different varnishes; films and varnishes can be chosen with a declaration of compliance for food contact. We also have board with a declaration of conformity for direct food contact. We work with 3-ply E, B and C boards, 5-ply EB, BE, BC and heavy AC, and 7-ply AAC. On request, we prepare a sample before the run to check colour and code reading on the chosen board. Most orders are delivered within 7 days (max. 16 working days). We tailor order quantities to your needs – we also make short runs and prototypes. If a construction requires a minimum quantity, we state it in the quote.

Sources

Regulation (EU) 2025/40 (PPWR) on EUR-Lex (Articles 3 and 12); Regulation (EC) No 1935/2004 on EUR-Lex (Article 3); Regulation (EC) No 2023/2006 on EUR-Lex (Annex, part A); GS1 on 2D barcodes and GS1 Digital Link; Andrzejak K., Garbowski T., Przegląd Papierniczy 77 (2021). Check the current texts before you decide: we did not find the PPWR implementing acts on labels in EUR-Lex on 13 November 2026.

What to send us

Send the box dimensions or the product, the quantity, the artwork or logo, the colours, whether you need codes or variable data, and whether the box will touch food. We produce boxes to your dimensions. Send your enquiry through our home page.

Frequently asked questions

When should I choose digital printing instead of flexo for corrugated boxes?

Choose digital printing when each box needs different data (serial numbers, QR codes, names), when you need many artwork versions or when the run is short or medium. Flexo suits long runs with fixed artwork in a few colours, because the cost of the plates is spread over many boxes. Where the break-even point lies depends on the number of versions, the board and the quantity, so we state it in the quote.

How many colours can you print with flexo?

Up to 4 colours. Each colour needs its own plate. For photographic or multicolour artwork, digital printing (pigment or UV) or litho-lamination is usually the better fit.

Can you match a Pantone colour on a corrugated box?

Yes, we match colours to a Pantone reference. The result also depends on the board: on brown kraft liners colours look darker than on a white liner, and not every Pantone colour can be reproduced from CMYK in digital printing. Approve the colour on a printed sample on the board chosen for production.

Does printing weaken a corrugated box?

It can. In one laboratory study (Przegląd Papierniczy, 2021), flexo printing lowered the edge crush resistance (ECT) of the tested boards by 2.0 to 12.6% and the calculated box compression strength by 5 to 11%, while UV-cured digital printing on the full surface did not lower them. Results depend on the plates, the pressure and the board, so for demanding loads ask for a test on the printed box.

Water-based or UV varnish: which one should I choose?

Water-based (dispersion) varnish is the standard protective coat for printed shipping boxes. UV varnish is cured by UV light and usually gives a higher gloss, so it is often used for spot effects on logos and for premium packs. Neither makes a box waterproof. Glue areas are normally left free of varnish, and for food packaging the declaration of compliance matters more than the type of varnish.

Will a QR code scan on brown corrugated board?

Usually yes, if it is printed dark on a light background, with a clear quiet zone (4 modules for QR, 1 module for DataMatrix), on a flat panel away from creases and flaps, and at a sufficient size. Avoid red codes, which red-light scanners may not read. Test the code on the production board and, if required, have it graded to ISO/IEC 15415.

Do shipping boxes need the PPWR label or a QR code?

Article 12(1) of Regulation (EU) 2025/40 requires a harmonised material label from 12 August 2028 or 24 months after the implementing acts, whichever is later. Transport packaging is exempt, but e-commerce packaging is not. A QR code with sorting information is optional. Status 13 November 2026; general information, not legal advice.

What files do you need for a printed box?

A PDF with vector logos and text, the colours named (CMYK or Pantone), the panels to be printed and, ideally, the artwork placed on our die line for your size. For variable data we also need a data file (CSV or XML) with one line per box. A spot varnish needs its own layer.