Corrugated Cartons for Automatic Packing Lines: How to Specify Boxes for Case Erectors, Case Packers and Sealers
A carton for an automatic packing line must above all be consistent. It arrives flat with the manufacturer’s joint already glued, and the machine expects every blank in the magazine to open square, fold at the creases and close the same way. Most stoppages come from warp, an uneven gap at the joint, out-of-square blanks, creases that do not fold cleanly and board that has taken up moisture. Specify these against your machine maker’s requirements and run a trial batch on your line before the series.
What the machines do with a carton
A packing line usually combines three steps, in one machine or several: erecting the box, filling it and closing it. Each step asks something different of the carton.
| Machine | What it does with the carton | What the carton must deliver |
|---|---|---|
| Case erector | Takes flat boxes from a magazine, often with suction cups, opens them, folds the bottom flaps and closes them with tape, hot-melt adhesive or staples | Flat blanks, a consistent joint, a square opening, creases that fold cleanly |
| Case packer, top-loading | Places the product into the erected box from above | Inside dimensions with the clearance your product and machine need |
| Case packer, end-loading | Slides the product into the box from the side | The same, plus an agreed loading face and flute direction |
| Wrap-around packer or tray former | Folds a flat scored and slotted sheet around or under the product and makes the closures | Accurate panels and creases, flat sheets |
| Case sealer | Closes the top flaps with tape or adhesive; uniform sealers are set for one size, random sealers take mixed sizes without adjustment | Flaps of equal length that meet without overlapping, a consistent box height |
Which construction suits machine erecting
The regular slotted container (FEFCO 0201) is the standard machine-erected box. The FEFCO code marks each style by current practice: M (usually manual erection), A (usually automated) or M/A (either). 0201 is marked M/A, while crash-lock-bottom styles such as 0711 and folder-type mailers such as 0427 are marked M. The marks are guidance, not a rule: to run another style on a machine, name the machine and ask (see FEFCO 0711 compared with 0201). Three details of a slotted box matter to the machine:
- The hand of the box. A flat box is “right hand” when the longer panel appears on the right and “left hand” when it appears on the left. The PMMI and Fibre Box Association call the hand a critical parameter to agree between the user and the machine maker.
- The joint. The joint tab sits inside or outside, is glued, stitched or taped, and can extend past the crease into the flaps. Agree which one your machine expects.
- Length and flute direction. Length is the larger dimension of the open face as the box is erected for loading, so the loading direction decides which dimension is called length. In top-opening boxes the flutes normally run vertically for stacking strength; in end-loading boxes the direction varies with the application.
Tolerances that matter on a machine
For regular slotted boxes of singlewall B- or C-flute board (ECT 4.5 to 7.7 kN/m) with panels of 10.2 to 63.5 cm, erected, filled and closed on automatic machinery, the technical report B155-TR2.1 (2018) of the PMMI and the Fibre Box Association gives these guide values, measured on the flat blank:
| Feature | Guide value | Why it matters on the line |
|---|---|---|
| Each panel, crease centre to crease centre | ±1.5 mm | Panel variations add up across the box |
| Overall size of the flat blank | ±3 mm | The machine is set to one blank size |
| Gap at the manufacturer’s joint, at the flap creases | 3 to 12.7 mm | The joint decides whether the box opens square |
| Difference in the joint gap on one box (skew or fishtail) | At most 4.5 mm; at least 1.5 mm gap at the flap ends | Skew together with joint variation is a common cause of jams |
| Slot depth; slot centring | ±3 mm; within 1.5 mm of the creases | Flaps fold without bulging |
| Gap between the major flaps after closing | No overlap, at most 6.4 mm | The sealer can close the box |
| Creases | A 180° fold (90° each way) without fracture or continuous cracking | Flaps fold where the machine expects |
| Warp | At most 6.4 mm in 305 mm, 12.7 mm in 610 mm, 19 mm in 915 mm, 25.4 mm in 1219 mm | Warped blanks feed badly from the magazine |
For high-speed lines of 50 or more per minute, the companion report for scored and slotted sheets and trays (B155-TR2.2, 2018) allows less warp, 4.8 mm in 305 mm and 9.5 mm in 610 mm, and asks the user to tell the supplier that the application is high speed. Both are voluntary reports, not standards, and allow other agreed values. The quality catalogue of the German corrugated board association VDW (version 4.4, 2014) also notes that machine converting may need special tolerances, leaves flatness to the specification, and accepts a glued joint if at least 80% of the glue surface is covered with fibres after tearing.
Our standard tolerances are ±4 mm on the box dimension and ±2 mm on creases. They are measured differently, so they are not directly comparable with the guide values. For a packing line we set tolerances from your machine maker’s requirements and can narrow our standard values by agreement (see tolerances on corrugated boxes).
Moisture, storage and vacuum pick-up
Paper takes up and gives off water from the air, so storage changes how a carton runs. The PMMI and Fibre Box Association recommend 4 to 38 °C and 30 to 70% relative humidity. Above 70% the board can change dimensions, warp and stick in machines because of higher friction; below 30% it can become brittle. If your store is outside that range, bring the cartons to the packing area in advance, in some cases 24 hours or more. Use the oldest stock first and run cartons on automatic machinery within 3 to 6 months of manufacture. Keep them flat in their bundles until use, and specify the strapping or wrapping if it could affect how they run. More in how to store corrugated boxes.
If your erector picks blanks with suction cups, warp, washboarding and surface irregularities let air in around the cup; the report on vacuum handling (B155-TR2.4, 2018) says this has more influence on the holding force than air drawn through the board. Tell your supplier where the cups sit.
A trial run on your line
- Share the machine data: type, closing method, speed, magazine orientation, the hand of the box and the machine maker’s carton requirements, with photos of the magazine.
- Check the fit with a prototype or plotter sample before tooling and the trial batch.
- Run the trial batch at normal speed with cartons conditioned like your normal stock, and record every stoppage.
- Measure the cartons that stopped and a sample of the rest: joint gap, skew, warp, panels and creases.
- Correct the board, flute direction, creases, joint or dimensions, and repeat if needed.
- Freeze the specification and keep an approved reference sample. A later change of board, construction or supplier deserves a new trial (see a second supplier for corrugated boxes).
Checklist: what to put in your enquiry
- Machine type, erecting and closing method, speed in cartons per minute, magazine orientation.
- FEFCO style, inside dimensions length × width × depth, top- or end-loading.
- Hand of the box, joint inside or outside, glued or stitched.
- Board grade, flute direction, weight and stacking load of the filled box.
- Tolerances your machine maker requires and whether the line is high speed.
- Print fields kept clear of glue, creases and suction-cup areas; codes the machine reads.
- Pieces per bundle, strapping, pallet type and how bundles face on the pallet.
- Storage conditions at your site, and what counts as a pass in the trial.
- Whether one size could serve several products (see right-sizing your boxes).
What we can do
We make cartons to your dimensions in slotted styles such as 0201, in folder-type and in die-cut constructions from the FEFCO code. Boards: 3-ply E, B and C flute; 5-ply EB, BE, BC and heavy AC; 7-ply AAC. Joints are glued on multi-point folder-gluers or stitched. On request we try a carton on your packing line, work with the supplier of your erecting machine and show your team how to pack, and we can review your size range to cut the number of sizes and the manual work. Board parameters (ECT, BCT) come from our board suppliers’ tests for every batch; package tests (compression, drop, transport simulation) can be arranged in a partner laboratory on individually agreed terms. We print by flexography or digitally in UV. For regular orders we can hold stock and deliver on call-off under an agreement. Most orders are delivered within 7 days (max. 16 working days); delivery within the EU is by agreement. We tailor order quantities to your needs – we also make short runs and prototypes. If a construction requires a minimum quantity, we state it in the quote.
Sources
PMMI and Fibre Box Association technical reports, 2018 editions: B155-TR2.1, regular slotted containers; B155-TR2.2, scored and slotted sheets and trays; B155-TR2.3, storage and handling; B155-TR2.4, handling with vacuum. FEFCO code (erection marks). VDW quality catalogue, English translation hosted by FEFCO. Editions as available on 13 November 2026; your machine maker’s requirements take precedence over guide values.
What to send us
Send the product and its dimensions, the machine type, closing method and speed, photos of the magazine and the machine maker’s carton requirements if you have them. We produce boxes to your dimensions and will propose a construction and a trial. Send your enquiry through our home page.
Frequently asked questions
Do cartons for a case erector have to be delivered flat?
Yes. Slotted boxes for a case erector are delivered knocked down: flat, with the manufacturer’s joint already glued or stitched, so that the machine can take them from the magazine, open them and close the bottom. Wrap-around blanks and trays come as flat sheets, and the line makes the joint and flap closures.
Which FEFCO style runs best on a case erector?
The regular slotted container, FEFCO 0201, is the usual machine-erected box, and the FEFCO code marks it M/A (manual or automated erection). Crash-lock-bottom styles such as 0711 and folder-type mailers such as 0427 are marked M (usually manual). The marks describe current practice, not a rule, so name your machine if you want another style.
What tolerances does an automatic packing line need?
The ones your machine maker specifies. As guide values, the PMMI and Fibre Box Association report B155-TR2.1 (2018) gives ±1.5 mm per panel, a joint gap of 3 to 12.7 mm, at most 4.5 mm skew and at most 6.4 mm warp in 305 mm. Our standard tolerances are ±4 mm on the box dimension and ±2 mm on creases; for a packing line we agree them individually and can narrow them.
Why do cartons jam in the magazine or fail to open square?
The usual causes are warp, an uneven or skewed gap at the manufacturer’s joint, tolerances that add up across panels, creases that do not fold cleanly, damaged edges and board that has taken up or lost moisture. A trial on your line with conditioned cartons shows which applies.
Do I need to tell you the brand and model of my machine?
It is not required, but it helps us choose the construction, the flute direction and the hand of the box. Photos of the magazine, the closing method, the speed and the machine maker’s carton requirements are often enough.
How should cartons be stored before they go on the line?
Flat, in their bundles, off the floor and away from open doors. The PMMI and Fibre Box Association recommend 4 to 38 °C and 30 to 70% relative humidity, conditioning in the packing area when the store is outside that range (in some cases 24 hours or more), first in, first out, and use on automatic machinery within 3 to 6 months of manufacture.
Can you test cartons on our packing line before the series?
Yes, on request. We can try a carton on your line, work with the supplier of your erecting machine and show your team how to pack. We correct the dimensions or the construction after the trial and only then produce the batch; scope and terms are agreed individually.