How to Store Corrugated Boxes: Humidity, Temperature, Stacking and Stock Rotation

Store corrugated boxes flat, indoors and off the floor, away from doorways and sources of moisture, in a stable climate. Industry guidance (FBA and PMMI) recommends 30–70% relative humidity and 4–38 °C. Humidity matters most: in a 2024 laboratory study, edge crush strength at 80% relative humidity was 60–76% of the value in the standard test climate. Use the oldest stock first, let cold deliveries reach room conditions before packing and stack filled boxes in aligned columns.

Recommended storage conditions

The figures below are voluntary guidelines, not legal limits. Sources were checked as of 13 November 2026.

Topic What the guidance says Source
Relative humidity 30–70% FBA and PMMI, technical report B155-TR2.3, 2018
Temperature 4–38 °C; avoid extremes and fluctuations FBA and PMMI
Place Indoors and under cover, away from sources of moisture and from doorways that are opened often; not directly on the floor FBA and PMMI
Position Flat (horizontal), knocked down, on clean flat pallets with all deck boards in place FBA and PMMI
Unit protection Banding, film and top and bottom boards stay in place until the cartons are used FBA and PMMI
Age Best run on automatic machines within 3–6 months of manufacture; containment and stacking function kept for at least 12 months under recommended conditions FBA and PMMI

Strength values in board datasheets are measured after conditioning in the standard climate of ISO 187: 23 °C and 50% relative humidity. A store that is more humid than that gives less strength than the datasheet. Very dry air is not ideal either: below 30% relative humidity board and its adhesive can become brittle and change dimensions, according to the FBA and PMMI.

How humidity affects strength

Paper fibres take up water from the air, swell and soften, and the moisture content of the board follows the humidity around it. Above 70% relative humidity the FBA and PMMI list softer board, lower stacking strength, changed dimensions, warp and, in extreme cases, softened adhesive and delamination. A study published in Applied Sciences in 2024 conditioned six 3- and 5-layer boards at 30–90% relative humidity and 10–60 °C and measured their edge crush strength (ECT). The values at 20 °C, as a share of the value in the standard climate, were:

Relative humidity at 20 °C ECT as a share of the standard-climate value (range for the six boards)
30% 107–119%
50% 93–99%
70% 79–93%
80% 60–76%
90% 34–47%

Other sources point the same way. A Fibre Box Association loss factor, quoted by the Renewable Bioproducts Institute at Georgia Tech, gives a 32% loss of box compression strength at 80% relative humidity, and the author’s moisture model predicts 27%. The NMFTA, citing the Fibre Box Handbook, says stacking strength can fall by more than 60% above 95% relative humidity. Changing humidity is worse than constant humidity: studies at the US Forest Products Laboratory found that the stacking life of loaded containers falls as humidity rises and falls further when it cycles.

These figures show a trend for specific boards, not a specification for yours. If cartons are stored in a humid warehouse or a cold room, plan a strength reserve with a suitable safety factor for stacking strength, or consider wax-free moisture-resistant boxes.

Cold deliveries, condensation and acclimatisation

When cold cartons are brought into a warmer, more humid room, water can condense on them; the German insurers’ Transport Information Service describes this cargo sweat for goods moved from cold to warm conditions. To avoid it:

  1. Bring the unit in closed. Move the pallet into the packing area with banding and film still on.
  2. Give it time. Wait until the cartons reach the conditions of the packing area. The FBA and PMMI say this may take 24 hours or more in some cases.
  3. Keep it off the floor and away from doors. A cold floor or an open doorway keeps the bottom layers damp.
  4. Use a third area if needed. If both the store and the packing area are outside the recommended range, the FBA and PMMI suggest conditioning the cartons in a third area.
  5. Keep bundles closed until use. Leave the banding and other unitising material in place until the cartons are needed (FBA and PMMI).

Stacking flat bundles and filled boxes

Flat cartons are delivered in bundles or units on pallets. Store them flat with no uneven weight on top, do not walk or stand on them, do not lift them by the straps and do not drop, throw or drag them: damaged edges and crushed flutes cause problems on erecting machines (FBA and PMMI). How many pallets of flat cartons may stand on top of each other depends on the load, so ask your supplier for the limit.

For filled boxes, the pallet pattern changes how much load the stack carries, because a box carries most of its load through its corners:

Pallet pattern Compression loss compared with a single box Source
Columnar aligned (corners above corners) 12–20% RIT study for the Fibre Box Association, 2021
Interlocked 49–54% RIT study for the Fibre Box Association, 2021
Hybrid (columns below, interlocked layers above) 45–49% RIT study for the Fibre Box Association, 2021
Interlocked or block, earlier studies 35–60% Literature review in the RIT study; a 2025 BioResources paper quotes 55% for block and 18% for column stacking from a 1963 study

Misaligned columns lose much of the column advantage: in the RIT tests, offset columns lost almost as much as interlocked stacks. Time under load lowers strength further, and more so in humid or changing conditions, which is why designers apply factors for time, humidity, pallet pattern and handling. The Fibre Box Association is updating these factors, so check the current edition of the Fibre Box Handbook. For counts and footprints on a pallet see how many boxes fit on a pallet, and for reading the cause of crushed boxes see damaged cartons in transit.

Stock rotation: first in, first out

  • Mark every pallet with its delivery date or batch, so the oldest stock is easy to find.
  • Issue the oldest stock first (first in, first out), as recommended by the FBA and PMMI.
  • Plan stock levels so that cartons for automatic machines are used within 3–6 months of manufacture.
  • Inspect before use for damp patches, warp and crushed or torn edges, and keep damaged cartons apart.
  • Order in batches that match consumption rather than one large delivery: smaller batches spend less time in the store.

Stitched and glued cartons in storage

The manufacturer’s joint of a slotted box can be glued, stitched or taped (FEFCO Code). We also make stitched cartons, in which steel wire staples replace the glue seam, for example for heavier goods (see heavy-duty boxes from AC and AAC board). The joint does not stop the board itself from absorbing moisture, so the storage rules above apply to stitched cartons too. Stitching wire and staples are sold in galvanised and copper-coated finishes that vendors describe as rust-resistant; if stitched cartons will be stored in damp conditions, ask your supplier which wire is used. Cartons sewn with thread instead of staples exist as a niche technique; we found no standards or independent storage data for them, and they are not part of our standard offer.

Checklist: what to agree with your supplier

  1. Your storage conditions. Humidity, temperature, cold rooms and how long cartons stay in store, so the board has a reserve.
  2. Board data. ECT and BCT values for the batch, measured in the standard climate.
  3. Unitising. Banding, film, top and bottom boards and a pallet with all deck boards.
  4. Stacking limit. How many pallets of flat cartons may stand on top of each other.
  5. Batch marking. Production date or batch number on each pallet for first in, first out.
  6. Delivery rhythm. Batch sizes matched to consumption, or stock held by the supplier and delivered on call-off.
  7. Joint and moisture options. Glued or stitched joint, the type of stitching wire, and whether a water-barrier board is needed.

What we can do

We produce corrugated boxes to your dimensions from 3-layer E, B and C board, 5-layer EB, BE, BC and heavy AC board, and 7-layer AAC board. Board parameters such as ECT and BCT come from our board suppliers’ tests for every batch, and we can arrange package tests (compression, drop, transport simulation) in a partner laboratory; terms are agreed individually. For humid storage we can make or source wax-free board with a water-barrier coating, and we make film-coated and varnished boxes. With regular cooperation we can hold stock of your cartons at our plant and deliver on call-off; we invoice per delivery or for the whole batch, as agreed in the contract, and larger regular customers can have consignment stock at their site, settled on usage. Most orders are delivered within 7 days (max. 16 working days); delivery within the EU is arranged by agreement. We tailor order quantities to your needs – we also make short runs and prototypes. If a construction requires a minimum quantity, we state it in the quote.

Sources

FBA and PMMI, Storage and Handling of Corrugated Packaging Materials (B155-TR2.3-2018); Mrówczyński et al., Impact of Temperature and Humidity on Key Mechanical Properties of Corrugated Board, Applied Sciences 2024; Popil, Effects of moisture content on box compression strength (Georgia Tech); Dunno and Ge, Influence of Pallet Pattern on Top to Bottom Compression Performance of Unitized Loads (RIT for the FBA, 2021); Kmita-Fudalej and Budzyński, BioResources 2025; Urbanik and Lee, Wood and Fiber Science 1995; Transport Information Service of the German insurers (GDV), corrugated board. All checked on 13 November 2026.

What to send us

Tell us what you pack, where and for how long the cartons are stored (humidity, temperature, cold room), how high you stack and how many cartons you use per month. We produce boxes to your dimensions. Send your enquiry through our home page.

See also: Packaging Supply Models for Manufacturers: Call-Off from Supplier Stock, Consignment, Kanban and Ordering from Your ERP

Frequently asked questions

At what humidity should corrugated boxes be stored?

Industry guidance recommends 30–70% relative humidity (FBA and PMMI, 2018); above 70%, board can soften, lose stacking strength and warp. Stable conditions matter as much as the level: avoid damp floors, open doorways and large swings in humidity.

How much strength does a carton lose in humid air?

It depends on the board. In a 2024 study of six 3- and 5-layer boards, edge crush strength at 20 °C was 60–76% of the standard-climate value at 80% relative humidity and 34–47% at 90%. A Fibre Box Association loss factor gives 32% lower box compression strength at 80%. Treat these as a trend, not as data for your board.

Can cartons be stored in a cold warehouse?

The FBA and PMMI recommend 4–38 °C. Below that range, and especially when cold cartons are brought into a warm, humid packing area, condensation can wet the board. Let the unit warm up in its wrapping before use.

How long should cartons acclimatise before packing?

Until they reach the conditions of the packing area. The FBA and PMMI say this may take 24 hours or more in some cases. Keep banding and film on during that time.

How long can empty corrugated boxes be stored?

According to the FBA and PMMI, unused cartons keep their containment and stacking function for at least 12 months from manufacture under recommended conditions, and they run best on automatic machines within 3–6 months. Use the oldest stock first.

Does the stacking pattern of filled boxes matter?

Yes. In tests for the Fibre Box Association published in 2021, boxes stacked in aligned columns lost 12–20% of their single-box compression strength, while interlocked stacks lost 49–54%. Earlier studies reported 35–60% for interlocked or block stacking.

Are stitched cartons better for damp storage?

The joint does not stop the board from absorbing moisture, so a stitched carton needs the same dry storage as a glued one. If stitched cartons will be stored in damp conditions, ask your supplier which stitching wire is used; galvanised and copper-coated finishes are sold as rust-resistant.

Can you hold stock of our cartons and deliver on call-off?

Yes, with regular cooperation we can hold stock of your cartons at our plant and deliver on call-off. We invoice per delivery or for the whole batch, as agreed in the contract, and larger regular customers can have consignment stock at their site, settled on usage. Delivery within the EU is arranged by agreement.