Damaged Cartons in Transit: How to Read the Cause and Prevent It

A damaged carton tells you what went wrong: the way it failed usually shows whether the board, the construction, the pallet pattern, moisture or the way the product was packed let it down. Before you order a stronger carton, read the cause. Often the answer is a lower stack, a better-fitting size or an insert. This guide is for purchasing, logistics and quality teams at importers, wholesalers, manufacturers and distributors who buy corrugated cartons and have to deal with damage. It gives a table of common failures, a method for collecting evidence, a worked stacking-strength example and a prevention checklist.

Common damage, causes and actions

What you see Most likely cause What to do
Crushed bottom cartons, walls folded vertically Stack overload: ECT or BCT too low, stack too high, long storage, moisture Calculate the required BCT, use board with a higher ECT or 5-layer board, lower the stack, limit moisture
Bulged side walls without crushing Overfilling, loose contents pressing on the walls, moisture Fit the size to the product, block the contents, add an insert or a layer pad
Dented corners and edges Impacts when handling or dropping; cartons overhanging the pallet Match the dimensions to the pallet, use a column pattern, use stronger board or corner protectors
Punctures or scuffing of a wall Sharp parts of the product, shifting contents, fork impact Block the product, keep sharp edges away from the wall with an insert, consider stronger board
Open flaps, failed seals Overfilling, weak closure, moisture, badly matched flap size Check carton height against the contents, choose the tape and closure method, consider stitching for heavy loads
Cracks along score lines Faulty scores, repeated folding, folding in the wrong direction Report to the supplier with a sample, check the construction and how it is folded
Soft, wet patches Water, condensation, storage on a cold floor or in a cold room Film and underlay, store on a pallet, choose board suited to the conditions
Shifted or collapsed pallet load No pallet securing, interlocked pattern, stack too high Stretch film or straps, column pattern, lower stack

Why the carton is not always at fault

A carton that crushed in a stack may have been too weak, but it may also have stood two levels higher than planned for a week in a damp warehouse. In the same way, a punctured wall more often comes from loose product than from board that is too thin. That is why we start the analysis from the conditions, not from changing the material. Strength is judged with numbers (ECT and BCT), explained in ECT, BCT and the McKee formula.

How to collect evidence for a damage analysis

  1. Keep the damaged carton and, if possible, a few undamaged ones from the same batch.
  2. Take photos of the whole carton, the point of damage, the labels and the pallet from several sides.
  3. Record the conditions: weight of the filled carton, stack height, storage time and place, transport route and type.
  4. Measure the outside and inside dimensions and check whether the carton overhung the pallet.
  5. Give the board code and construction (FEFCO code) or the order number the carton came from.
  6. Send everything to your packaging supplier with a description of the problem.

Liability for a damaged shipment is a separate matter between the parties and the carrier. Whatever the outcome, the photos and the packaging are the evidence, so keep them.

Stacking strength: a worked example

Illustrative figures only. Six cartons are stacked on top of each other and each weighs 12 kg when filled.

Step Calculation Result
Cartons above the bottom one 6 minus 1 5 cartons
Mass carried by the bottom carton 5 x 12 kg 60 kg
Force from that mass 60 kg x 9.81 m/s² about 589 N
With a safety factor of 4 589 N x 4 about 2.4 kN

The bottom carton therefore needs a compression strength (BCT) of about 2.4 kN or more, which is then compared with the BCT of the finished carton, estimated from ECT, board thickness and carton perimeter and confirmed by a test. If humidity or long storage apply, the safety factor should be at the upper end or higher.

Three illustrative cases: how to read them

These are simplified examples, not descriptions of particular orders.

  • Bottom cartons crushed, top ones untouched. This is the pattern of stack overload. Check how many cartons stood above the bottom one and for how long, then compare the required BCT with the strength of the carton. A lower stack, board with a higher ECT or a column pattern usually helps.
  • Punctures on one side of the carton only. They point to contents shifting in one direction or to contact with forks. Block the product with an insert or a layer pad and check that the clearance is not too large.
  • Bulged, softened walls after cold-room storage. This is a combination of moisture and load. Increase the strength reserve (for example 5-layer board instead of 3-layer), lower the stack and reduce contact between the carton and the cold floor.

How to prevent damage

  • Calculate stack strength instead of guessing: required BCT = (number of cartons in the stack minus 1) x carton weight x a safety factor, often 3 to 5.
  • Match the carton to the pallet and avoid overhang: see how many boxes fit on a pallet.
  • Block the product with layer pads, dividers or inserts rather than loose fill, and choose a carton that fits: right-sizing your cartons.
  • Match the board to the conditions: moisture, cold rooms and long storage need a strength reserve, see crates and trays for fruit and vegetables for the effect of humidity.
  • Use the right pallet accessories such as layer pads and corner protectors: corrugated pallet packaging.
  • Test a new carton on a prototype before a large order.

For very heavy products see our article on heavy-duty AC and AAC board.

Cartons matched to your product

We choose board and construction to match the weight of the product, the stack and the transport conditions, and we check new solutions on a prototype. Send us the problem through our home page, with photos of the damaged carton if you have them. We reply with a quotation within a few hours on working days, most orders leave our plant within 7 days (max. 16 working days) and we ship from Poland across Europe. Read the guide to buying cartons from Poland, our bulk offer and our wholesale terms.

See also: Corrugated Packaging for Glassware, Porcelain and Ceramics: Dividers, Inserts and Pack Testing

See also: Void Fill and Product Protection Compared: Paper, Corrugated Inserts, Air Pillows and Foam

See also: Handling Marks on Cartons (ISO 780): What the Symbols Mean and Where to Print Them

See also: Goods-Receipt Inspection for Corrugated Boxes: A Checklist, and How to File a Complaint That Gets Resolved

Frequently asked questions

How can I tell that a carton was overloaded in the stack?

The bottom cartons are crushed and their walls are folded or bulged vertically. The cartons at the bottom of the stack and near the pallet edges usually suffer most.

Does humidity really lower the strength of a carton?

Yes. Corrugated board absorbs moisture from the air and loses part of its strength, especially during long storage under load. Cold rooms and damp warehouses therefore need a strength reserve or a different board.

What should I do with a damaged batch of cartons?

Keep samples and photos, note the storage and transport conditions and send them to your packaging supplier. That is what allows the cause to be placed with the board, the construction or the way the carton was used.

Does a stronger board always solve the problem?

No. If the cause is loose product, a poor pallet pattern or a stack that is too high, stronger board only raises the cost. Find the cause first.

How do I calculate the strength a carton needs?

Required BCT = (number of cartons in the stack minus 1) x weight of one carton x a safety factor, often 3 to 5. Compare the result with the compression strength of the finished carton, and confirm it with a test or a prototype.

Can you analyse photos of damaged cartons?

Yes. Send photos, the board and construction code or the order number, the stack height, storage time and transport route, and we will help place the cause.