Goods-Receipt Inspection for Corrugated Boxes: A Checklist, and How to File a Complaint That Gets Resolved
Check a delivery of corrugated boxes in two steps. At the dock, before you sign, compare the delivery note with your order, count the pallets and bundles, and check the wrapping for damage, moisture and crushing; note any visible damage on the delivery document. Then, once the boxes have reached room conditions, check a random sample against the specification: dimensions, creases, board, joint, print and count. If something is wrong, hold the lot and report it with photos, measurements and the delivery number. As of 18 November 2026.
Step 1: at the dock, before you sign
- Documents. Compare the delivery note with the order: article number and version, quantity, number of pallets and bundles.
- Units. Count the pallets and, where the bundles are visible, the bundles on each pallet.
- Pallets and wrapping. Look for broken pallets, missing deck boards, torn film, loose straps and leaning loads. The FBA and PMMI recommend keeping flat boxes on pallets with all deck boards in place and leaving the banding and film on until the boxes are used.
- Moisture. Check for wet patches, water stains, condensation under the film and soft or wavy board, especially in the bottom and top layers.
- Crushing. Look at the corners, the edges and the top of each pallet for crushed bundles and forklift damage.
- Labels. Check that the pallet labels are legible and match the delivery note.
If anything is visibly wrong, take photos before unloading continues and write a short, specific remark on the delivery document before you sign, for example “pallet 3: film torn, top layer wet”. For international carriage by road, Article 30 of the CMR Convention treats taking delivery without reservations as prima facie evidence that the goods arrived in the condition described in the consignment note; for loss or damage that is not apparent, written reservations are due within 7 days of delivery, Sundays and public holidays excepted. National rules and your contracts may differ: this is general information, not legal advice. To read the cause of transport damage, see damaged cartons in transit.
Step 2: the inspection checklist
Inspect once the boxes have reached the conditions of the room where you measure: paper takes up and gives off moisture, and a box straight from a cold truck measures differently (see how to store corrugated boxes). The reference is your specification (see how to write a specification for a corrugated box).
| What to check | How | Typical finding |
|---|---|---|
| Article and version | Compare the bundle and pallet labels, the boxes and the delivery note with the order | An old version of the print, or the wrong size under the right article number |
| Quantity | Count the pieces in several bundles and multiply by the number of bundles; compare the total with the agreed quantity tolerance | Bundles with fewer pieces than their label states |
| Flatness and moisture | Lay flat boxes on a table, look along the edges and feel the board | Warp, wavy or soft board, damp patches |
| Dimensions | Erect several boxes and measure the inside length × width × height in millimetres, or use the method named in the specification (see internal or external dimensions) | A dimension outside tolerance; inside and outside dimensions confused |
| Creases and slots | Fold the panels and flaps along the creases | A crease that folds in the wrong place, a cracked outer liner, slots out of position |
| Board | Look at a cut edge: number of layers, flute, liner colour | A different flute or grade from the order, liners coming away from the flutes |
| Joint | Check the glued, stitched or taped joint; on one sample box, tear a glued joint by hand | Glue that comes apart without tearing fibres, panels misaligned at the joint, loose or missing stitches |
| Compare with the approved artwork and the reference sample; scan any barcode or QR code | Wrong content, colour clearly off the reference, smudged or incomplete print, print out of position | |
| Function | Erect and close a few boxes by hand or on your line, and pack a product | Boxes that do not square up, flaps that do not meet, stoppages on the machine |
The VDW quality catalogue checks most of these characteristics; for a glued joint it expects torn fibres over most of the glue area after tearing. Tolerances on dimensions, creases and quantity are explained in tolerances on corrugated boxes.
How to take a sample
- At random, across the delivery. Take boxes from several pallets and from the beginning, the middle and the end of the shipment, as the VDW catalogue recommends, not only from the top bundle.
- To an agreed plan. The number of boxes and the number of defects allowed should come from the specification. Common plans are based on ISO 2859-1, which indexes sampling schemes by acceptance quality limit (AQL); its current edition is from 2026.
- By defect class. Sort findings into critical, major and minor defects, as in the VDW catalogue. A critical defect, such as the wrong construction or the wrong flute, can on its own lead to rejection of the delivery.
- Separately for transport damage. The VDW catalogue excludes boxes made unusable in transport from the evaluation of production quality; report them as transport damage.
- In a stable climate. If a measurement is disputed, repeat it after conditioning in the standard atmosphere of ISO 187: 23 °C and 50% relative humidity.
What to do with a suspect lot
- Put it on hold. Label the pallets, keep them apart and do not use or scrap them until the case is agreed.
- Find the scope. Check whether the problem affects one pallet, one production date or the whole delivery, and whether earlier deliveries still in stock are affected.
- Report early. Tell the supplier on the day you find the problem, even before all measurements are done.
- Agree the next step. Sorting, replacement or return; if you need part of the lot urgently, agree in writing which boxes may be used.
- Keep the evidence. Keep the defective boxes, some good ones from the same lot, the labels and the wrapping.
How to file a complaint that gets resolved
A complaint is settled faster when the supplier can see the facts without asking twice. Send:
| What to send | Why it matters |
|---|---|
| Delivery note or invoice number, article number and version | Identifies the order, the specification and the production run |
| Photos of the pallet label and of the whole pallet | Links the defect to a pallet and shows its condition on arrival |
| Close-up photos with a ruler or tape measure in the picture | Shows the size and the position of the defect |
| Measured values: how many boxes, the results, the method and the room conditions | Allows a comparison with the specification and the tolerances |
| Number of affected boxes or pallets, and where the problem was found (goods receipt, store or packing line) | Shows the scope and helps to separate production defects from storage or transport damage |
| What you need, and by when | Lets the supplier plan production and transport |
Describe what you saw and measured, not your conclusions, and keep the samples available for collection or send a few on request.
Common mistakes
- Signing for a visibly damaged delivery without a remark.
- Using or scrapping the lot before the supplier has seen the evidence.
- Measuring a single box, or boxes straight from a cold truck.
- Measuring outside dimensions against an inside specification.
- Treating a quantity difference within the agreed tolerance as a shortage.
- Photos without a label, a scale or a delivery number.
- Reporting a problem weeks later, when the boxes are mixed with other deliveries.
How complaints work at Kartoniki.eu
Send us photos, the measured dimensions, the number of pieces affected and the delivery number. We give a first response within 24 hours on working days and review every case individually. Depending on the case, the resolution is a replacement of the goods, a corrective invoice, a refund or collection of the defective goods; the details are set in the contract. We invoice the quantity actually delivered. You speak directly, by phone, with the person who handles your order and knows production, with no hotline or ticket system in between.
If we deliver neutrally to your customers on your behalf, agree with us in advance who checks those deliveries and how a complaint reaches us (see neutral boxes and direct delivery for distributors). If you want to see how we work before you order, visits and audits of our plant are possible (see auditing a corrugated packaging supplier).
Sources
VDW quality catalogue for corrugated board packaging (English translation hosted by FEFCO, version 4.4, 2014); FBA and PMMI, storage and handling of corrugated packaging materials (2018); ISO 2859-1:2026 and ISO 187:2022; CMR Convention (UNECE, Article 30). Industry documents are voluntary references. Checked on 18 November 2026.
What to send us
Send us your specification or a sample box and tell us how you inspect deliveries, so that the quote is based on the same criteria as your goods receipt. Send your enquiry through our home page.
Frequently asked questions
What should I check when a delivery of corrugated boxes arrives?
At the dock: the delivery note against the order, the number of pallets and bundles, the condition of the pallets and wrapping, and signs of moisture or crushing. Then, on a random sample: article and version, quantity, flatness, dimensions, creases, board, joint, print and how the boxes erect and close.
Should I sign the delivery note if a pallet is damaged?
Write a short, specific remark about the visible damage on the delivery document before you sign, and take photos. Under Article 30 of the CMR Convention, which covers international carriage by road, taking delivery without reservations is prima facie evidence that the goods arrived as described in the consignment note. General information, not legal advice.
How many boxes should I inspect?
As many as the sampling plan in your specification says. Plans for corrugated packaging are often based on ISO 2859-1: the size of the lot sets the sample size, and the acceptance quality limit (AQL) sets the number of defects allowed. Take the boxes at random from several pallets, not only from the top bundle.
When should I measure delivered boxes?
After they have reached the conditions of the room where you measure, because paper changes with humidity. If a measurement is disputed, repeat it after conditioning in the standard atmosphere of ISO 187: 23 °C and 50% relative humidity.
The delivered quantity differs from the order. Is that a reason for a complaint?
Not if the difference is within the agreed quantity tolerance; we invoice the quantity actually delivered. If the difference is outside the tolerance, or bundles contain fewer pieces than their labels state, report it with your counts.
What should I do with a defective lot while the complaint is open?
Put it on hold: label it, keep it apart and do not use or scrap it until the case is agreed. If you need part of it urgently, agree in writing with the supplier which boxes may be used.
What evidence does a supplier need?
The delivery note or invoice number, the article number and version, photos of the pallet label and of the defect with a scale, the measured values with the method, the number of affected boxes and where the problem was found.
How quickly does Kartoniki.eu respond to a complaint?
We give a first response within 24 hours on working days. Depending on the case, we replace the goods, issue a corrective invoice, refund the amount or collect the defective goods; the details are set in the contract.