Tolerances on Corrugated Boxes: Dimensions, Creases, Grammage and Delivered Quantity – What Is Normal and How to Specify It
Our standard tolerances on corrugated boxes are ±4 mm on a box dimension, ±2 mm on the position of crease lines and ±5% on board grammage. The delivered quantity may differ from the order by ±8% up to 500 pieces, narrowing to ±4% above 5,000 pieces, and we invoice the quantity actually delivered. These are our standard values: if we agree otherwise, we can narrow them.
Corrugated board is made of paper, so every supplier works within tolerances. This article explains why, how to measure them and how to write them into an enquiry, with references to the FEFCO code, ISO test methods and two published industry documents. It is general information, not legal advice, and reflects the situation on 6 November 2026.
Our standard tolerances
| What is checked | Standard tolerance | Notes |
|---|---|---|
| Box dimension (length, width, height) | ±4 mm | Applies to the dimension stated in the quote, inside or outside |
| Position of crease (score) lines | ±2 mm | Matters where the box must fit a product or an insert closely |
| Board grammage (g/m²) | ±5% | Datasheet values are nominal |
| Quantity delivered | ±4% to ±8% | Depends on the order size, see below; we invoice the quantity actually delivered |
The quote always says whether a dimension is inside or outside, and the tolerance applies to that dimension. Measured grammage and strength can differ from the nominal values by a few per cent. If you need narrower tolerances, write the required values in the enquiry and on the drawing, and the quote confirms whether we can keep them.
Why corrugated board is not a precision material
A tolerance is the range in which a box still does its job. Four things keep corrugated board from behaving like metal or plastic:
- Moisture. Paper fibres take up water from the air, and that water changes the dimensions of the paper. Temperature and humidity also change the stiffness and strength of corrugated board significantly. A carton measured in a damp warehouse can give a different reading from the same carton in a dry office.
- Creasing. A crease is made by deliberately crushing the flutes along a line so that the board can fold. Board thickness is lost in the corners, so the flat blank, the cut and creased sheet before folding, is larger than the erected box, and the width of the crease depends on the flute, the papers and the creasing pattern.
- Board thickness. The thickness of finished board depends on processing as well as on the flute type, so it is an approximate value.
- Converting. Printing, creasing, slotting, die-cutting, folding and gluing each add a small deviation. That is why industry catalogues give separate tolerances for panels, die-cuts, slots and gaps, and check warp (flatness) on its own.
What is measured, and how
Which dimension
By convention, box dimensions are inside length × width × height in millimetres. The FEFCO code adds that they should be measured under standard climate conditions on the flat blank, from the centre of the crease, with the thickness of the material in mind. Industry documents also measure from crease centre line to crease centre line (see the references below). On a delivery it is quicker to measure the inside of the erected carton. The two readings differ by an allowance for board thickness, so name the method in your specification. See internal or external dimensions: how to specify a corrugated box.
In which climate
Because paper takes up and gives off water, compare only readings taken in the same conditions: measure several pieces, not one, in a stable room. The reference is the standard atmosphere for conditioning and testing paper and board in ISO 187: 23 °C and 50% relative humidity. The VDW catalogue below bases arbitration tests on it as well.
Which test method
If a value matters, name the method in the specification:
| Property | Standard | What it covers |
|---|---|---|
| Grammage | ISO 536:2019 | Grammage of paper and board |
| Grammage of the component papers | ISO 3039:2010 | Papers of corrugated board after separation |
| Board thickness | ISO 3034:2011 | Single sheet thickness of corrugated fibreboard |
| Edge crush resistance (ECT) | ISO 3037:2022 | Strength of the board, not its size |
| Conditioning and test atmosphere | ISO 187:2022 | 23 °C and 50% relative humidity |
| Acceptance sampling | ISO 2859-1:2026 | Sampling plans indexed by acceptance quality limit (AQL) |
A standard names a method, not a certificate. Referring to it in your enquiry fixes how a value is measured; it does not say that any supplier is certified to it.
What published industry references show
Two industry documents show the order of magnitude: the quality catalogue of the German corrugated board association VDW (English translation hosted by FEFCO) and a voluntary technical report of a US packaging machinery association and the Fibre Box Association. Both measure on the flat blank between crease centre lines, not on the erected box, and each has its own scope, so use them for orientation, not as a guarantee.
| Reference | Feature | Tolerance |
|---|---|---|
| VDW quality catalogue (version 4.4, 2014) | Distance between crease centre lines | ±3 mm up to 300 mm; ±4 mm over 300 to 700 mm; ±0.6% over 700 to 1,200 mm |
| VDW quality catalogue (version 4.4, 2014) | Position of slots | ±2 mm |
| PMMI/FBA technical report B155-TR2.2 (2018, panels of 10.2 to 63.5 cm, automatic packaging machinery) | Panel dimension, crease to crease | ±1.5 mm |
| PMMI/FBA technical report B155-TR2.2 (2018) | Overall dimensions of the flat sheet | ±3 mm |
Our standard ±4 mm applies to the box dimension as quoted, so it is not directly comparable with these figures. As an order of magnitude, a few millimetres is normal. Both documents leave room for other values by agreement.
Delivered quantity: why it differs and how it is settled
The number of good pieces in a run depends on how the machines are set up and on quality control, so a delivery can be slightly above or below the order. Suppliers state their own quantity bands in their terms of sale. The bands differ between suppliers and are often wider for small orders, so read the quantity clause of every quote as carefully as the price. Our standard bands depend on the order size:
| Order size | Quantity tolerance | Example (illustration, not an offer) |
|---|---|---|
| Up to 500 pieces | ±8% | Order of 400: delivery of 368 to 432 |
| 501 to 1,000 pieces | ±6% | Order of 1,000: delivery of 940 to 1,060 |
| 1,001 to 5,000 pieces | ±5% | Order of 2,000: delivery of 1,900 to 2,100 |
| Over 5,000 pieces | ±4% | Order of 6,000: delivery of 5,760 to 6,240 |
We invoice the quantity actually delivered, so the amount invoiced follows the delivery (see what drives the price of custom corrugated boxes). If you need an exact count, for example for kits with fixed contents, say so in the enquiry. If you order several sizes or call-off deliveries, ask whether the band applies to each size and each delivery or to the whole order.
How to write tolerances into an enquiry
Use this checklist when you write a specification or compare quotes:
- Drawing or code. Give a drawing or the FEFCO code with length × width × height in millimetres, marked inside or outside.
- Critical dimensions. Mark the one or two dimensions that decide the fit and leave the rest at the standard tolerance. Allow clearance for the tolerance, but no more: an oversized box wastes board and filler (right-sizing boxes).
- Tolerances. Write the values you need for each critical dimension and for the crease position. Tolerances add up across a chain of parts: two parts of ±4 mm each can end up 8 mm apart in the worst case (illustration). For cartons erected or packed by machine, give us the machine requirements, because then the tolerances come from the machine and we agree them individually.
- Board. Name the board (layers and flute) and, if strength matters, the ECT, because grammage alone does not describe strength (ECT, BCT and the McKee formula). If you check grammage, name the method and the climate.
- Quantity. Say whether the standard band is acceptable or you need an exact count, whether the band applies per size or to the whole order, and whether it applies to each call-off delivery.
- Reference sample. Agree a prototype or an approved sample that both sides keep as the physical reference for fit, creases and print.
- Measuring method. State who measures, how many pieces, where (the inside of the erected carton or the flat blank between crease centre lines), with which instrument and in which climate.
- Acceptance criteria. Define what counts as a defect and how many are acceptable in a sample, for example with a sampling plan based on ISO 2859-1, what happens to a lot that fails, and that a disputed lot is re-measured at the standard atmosphere.
For the other points of an enquiry see corrugated packaging for business buyers: 15 answers.
Sources
FEFCO: FEFCO code and the VDW quality catalogue for corrugated board packaging (English translation, version 4.4). PMMI and Fibre Box Association: technical report B155-TR2.2 (2018). ISO standards: ISO 536:2019, ISO 3039:2010, ISO 3034:2011, ISO 3037:2022, ISO 187:2022 and ISO 2859-1:2026. Research: Mrówczyński et al., Applied Sciences 2024 (temperature, humidity and the mechanical properties of corrugated board); Larsson, KTH thesis 2008 (dimensional stability of paper); Lindner, Journal of Materials Science 2018 (hygroexpansion of paper); Considine et al., TAPPI Journal 2026 (scoring of corrugated fiberboard). Industry documents are voluntary references, not legal requirements. Check the current editions before you decide.
What to send us
Send the drawing or the inside dimensions, mark the dimensions that decide the fit and write down the tolerances you need. The quote states the dimensions, inside or outside, and confirms whether we can keep your tolerances. We tailor order quantities to your needs – we also make short runs and prototypes. If a construction requires a minimum quantity, we state it in the quote. Send your enquiry through our home page.
Frequently asked questions
What is the standard tolerance on the dimensions of a corrugated box?
Our standard tolerance is ±4 mm on a box dimension and ±2 mm on the position of crease lines, with ±5% on board grammage. It applies to the dimension stated in the quote, inside or outside. These are standard values: if we agree otherwise, we can narrow them.
Will I receive exactly the quantity I ordered?
Not necessarily. The delivered quantity may differ from the order by ±8% up to 500 pieces, ±6% from 501 to 1,000 pieces, ±5% from 1,001 to 5,000 pieces and ±4% above 5,000 pieces. We invoice the quantity actually delivered.
Can the tolerances be narrower?
Yes. Write the required values in the enquiry and on the drawing, and the quote confirms whether we can keep them. For cartons erected or packed by machine, the tolerances come from the machine, so we agree them individually.
Does the tolerance apply to the inside or the outside dimension?
To the dimension stated in the quote. The usual convention, also used in the FEFCO code, is inside length × width × height in millimetres, but a quote can also be written for outside dimensions, so always say which one you mean.
Does the ±5% grammage tolerance mean the board can be lighter than in the offer?
Board grammage is a nominal value with a tolerance of ±5%, and the weight of a finished carton also changes with humidity. For comparisons, weigh several pieces and use stable room conditions or the standard atmosphere of 23 °C and 50% relative humidity.
How do I measure a delivered carton?
Measure the inside length × width × height in millimetres on the erected carton, on several pieces from the delivery, in stable room conditions, and compare the result with the dimension in the quote. Where the fit is critical, measure the crease positions too. The FEFCO code measures on the flat blank from the centre of the crease, so name your method in the specification.
Which standards describe how to measure corrugated board?
Examples are ISO 536 for the grammage of paper and board, ISO 3039 for the grammage of the component papers of corrugated board, ISO 3034 for the thickness of corrugated board, ISO 3037 for edge crush resistance and ISO 187 for the standard conditioning atmosphere. A standard names a method, not a certificate: referring to it fixes how a value is measured and does not say that a supplier is certified to it.
What should I do if a delivery is outside tolerance?
Send us photos, the measured dimensions of the pieces, the number of pieces and the invoice or delivery-note number. We review every case individually.