Corrugated Packaging for Electronics and Industrial Automation: Cartons, Inserts and Dividers Made to Size
Corrugated packaging for electronics means unit and outer cartons with inserts that hold the device in one position and protect the housing, connectors and displays. We make it to size for manufacturers of controllers, power supplies, modules, sensors and cabling, and for companies that assemble industrial automation equipment. In this sector packaging has two jobs: to protect the product in transport and to make work easier at the packing station and for the receiver. Instead of loose filling we therefore propose a formed board insert fitted to the shape of the device. We prepare a quotation within a few hours on working days and most orders leave our plant within 7 days (max. 16 working days).
How we build packaging for devices
For lighter devices the standard is carton of 3-layer board with flute E or B, and for heavier components and outer packs 5-layer board. The construction is matched to the product: a slotted carton, a folding one, one with a cut insert or one with layer pads. The styles are explained in the FEFCO catalogue and in our article on die-cut and slotted cartons.
- A unit carton printed with technical data and markings.
- A formed insert with a cavity for the device and separate places for the power supply, cables and documents.
- Dividers and grids in outer cartons, for example for modules or sensors.
- Layer pads between layers in cartons and on pallets.
- Board corner protectors guarding the edges of housings and parcels on a pallet.
Risk, solution and data for a quotation
| Risk to the product | Solution in the pack | What to give for a quotation |
|---|---|---|
| Damage to the housing or scratching | Formed insert, carton without slack | Dimensions, shape of the housing, sensitive surfaces |
| Bent or broken connectors and sockets | Insert with a cavity that relieves the connector | Layout of connectors, direction of leads |
| Loss of accessories, cables, documents | Separate compartments in the insert | List of items in the set |
| Pieces knocking together in an outer carton | Dividers, grids, layer pads | Dimensions and weight of a piece, pieces per carton |
| Moisture and static electricity | Additional protection agreed individually | Receiver’s requirements, storage conditions |
An insert instead of loose filling
Loose filling shifts in transport and can be a nuisance for the receiver after the carton is opened. A board insert holds the product in a fixed position, shortens packing time and organises the contents of the set in a repeatable way. The product does not touch the walls of the carton, so knocks and pressure are carried by the insert.
Inserts are made in any size. If you make several models of similar size, consider standardising: one carton and inserts with different cavities. This reduces the number of stock items and simplifies orders.
For products of complex shape, for example controllers with protruding connectors, the insert can be split into two parts: a lower one in which the device lies and an upper one that presses it from the lid side. The pack then stays stable even if the carton is tipped or turned during handling. Check such a layout on a prototype before ordering the whole batch. In outer cartons for modules, sensors or power supplies we use dividers so that the pieces do not touch each other with their housings; this also lets you count the contents quickly at goods-in and picks single pieces easily on an assembly line.
Who we prepare this packaging for
- Manufacturers of electronic devices and modules.
- Automation companies: controllers, power supplies, sensors, drives.
- Integrators and assembly plants that pack complete sets.
- Distributors of components who send parcels to business customers.
- Online shops with electronic equipment and accessories; see e-commerce packaging.
- Service centres sending devices for repair and returns.
Print, ESD and finish
On cartons we print technical data, markings, codes and a logo, by flexo in up to four colours or digitally. For a higher presentation standard we can use lamination and varnish, and for retail versions a film window. Short runs are described in short-run corrugated cartons.
Electrostatic protection (ESD) is a matter for individual agreement. If your documentation requires ESD materials, for example in inserts or films, say so in the enquiry and we will discuss how to use them in the pack. We do not declare certification or compliance with ESD standards: the requirements in this area are given by the receiver. Moisture is covered in packaging for humidity, cold, corrosion and sensitive loads.
Selection tips for buyers and technologists
- Measure the device together with protruding parts: connectors, antennas, knobs.
- List what else goes into the carton: power supply, cable, manual, screws.
- Decide on onward shipping. With couriers, dimensional weight counts; see dimensional weight and choosing a carton.
- Decide whether the carton is retail or purely logistic, because print and finish depend on it.
- Ask for a prototype if the insert has to hold a product of complex shape.
What to put in an enquiry
- Photos of the device, its dimensions with protruding parts and its weight.
- The list of items in the set.
- Requirements for ESD, markings and labels, if any.
- Storage conditions and the way of onward shipping.
- Whether the carton is retail or logistic, and the print needed.
How to order
Send the details through our home page, with photos of the device, the list of items in the set and any requirements for ESD, markings and labels. We reply with a quotation within a few hours on working days and most orders leave our plant within 7 days; orders that need artwork approval, test prints, plotter samples, a new cutting die or a very complex construction take longer, up to 16 working days. We ship from Poland across Europe and can make a prototype before the run. Read the guide to buying cartons from Poland and our wholesale terms.
Frequently asked questions
Do you make inserts for electronic devices?
Yes. We make formed inserts, layer pads, dividers and grids to size, in any dimensions. An insert has a cavity fitted to the device and separate places for accessories. For a quotation give the dimensions of the device and the list of items in the set.
Do you have anti-static packaging made of board?
ESD protection is an option agreed individually, for example through ESD materials in inserts or films. We do not declare certification or compliance with ESD standards. If you require ESD, describe the requirements in the enquiry and we will discuss the options.
What board suits electronics packaging?
For lighter devices 3-layer board with flute E or B is most often used, and for heavier components and outer cartons 5-layer. The choice depends on weight, stacking and the transport route. We will choose the board once you give the weight and the planned load.
Can I order a carton printed with technical data?
Yes. We print by flexo in up to four colours or digitally: technical data, markings, codes and a logo. For retail cartons lamination, varnish or a film window can be added.
Will the packaging work for courier shipping?
Yes, as long as the dimensions and the board are matched to the weight and the route of the parcel. Remember dimensional weight: an oversized carton raises the shipping cost. A fitted insert lets you reduce the outer dimensions of the pack.
How quickly will you prepare a quotation and the packaging?
We send a quotation within a few hours on working days and most orders leave our plant within 7 days (max. 16 working days). We can make a prototype before the run. We ship from Poland across Europe.