Packaging for Lamps and Lighting Products: Boxes, Inserts and Outer Cartons for Bulbs, LED Tubes and Luminaires
Packaging for lamps and lighting means corrugated boxes and inserts made to fit fragile, oddly shaped products: bulbs, LED tubes, ceiling lights, pendant lamps, lampshades, LED strips and drivers. What protects them is the inside of the box: an insert cut to the product that keeps glass away from the walls and from the next piece, with as little play as possible. The outer box carries the board strength, the print and, for light sources sold on their own, the EU energy label. Status 13 November 2026.
Lighting products and their transport risks
Lighting has no single typical shape, so the construction follows the product. The table shows the most common cases.
| Product | Typical packaging | Main risk | What to watch |
|---|---|---|---|
| Light bulbs | Unit box with a formed insert, or an outer carton with a divider lattice | Glass breaking against a wall or another bulb | Each bulb in its own seat or cell |
| LED tubes and fluorescent tubes | Rectangular tube-type box or telescopic box; outer cartons with layer pads | Bending and breaking of a long, narrow product | Length, cross-section, support along the whole length |
| Ceiling lights and surface-mounted luminaires | Box with an insert that holds the product away from the walls, plus corner pieces | Diffusers, brackets and parts that stick out | Separate place for the diffuser and the mounting kit |
| Pendant lamps and chandeliers | Larger box with a seat for the body and separate compartments for shades and cables | Irregular shape, arms and shades that deform easily | Shade and metal body kept apart |
| Floor and table lamps with shades | Long box for the stand, separate box or compartment for the shade | Crushed or dented shades | The shade must not carry any load |
| LED strips, cables and drivers | Die-cut box with print or a window | Several small items in one set | Compartments for each item, room for documents |
Glass and delicate shades are rarely broken by one hard impact. More often the cause is vibration and a small but repeated movement of the product inside the box. The rules for vessels and divider grids are the same as for tableware, see packaging for glassware, porcelain and ceramics.
Choosing the board and the box size
For light products such as bulbs and small luminaires we use 3-layer board (E or B flute, depending on the product). For heavier luminaires and outer cartons we use 5-layer board (EB, BE or BC), and for the largest and heaviest sets the heavy 5-layer AC or 7-layer AAC. The outer liner can be brown kraft or white, which matters when the box needs clean print. We do not state a load capacity in kilograms: the right board depends on the weight of the product, the number of pieces per carton, stacking and the route.
Size limits by construction: die-cut boxes up to 260 x 150 cm, rectangular tube-type boxes up to 240 cm inside length, telescopic boxes for many metres and very large cartons up to 10 x 3 m. Long products are covered in more detail in rectangular tube-type boxes for long products. For many models of similar size, consider one outer box with different inserts: fewer stock items and even pallet layers.
Inserts, dividers and layer pads
We make dividers, lattices, inserts and fillers from corrugated board in any size. These are the principles we apply when designing a lighting pack:
- An insert cut to the product. Openings, slots and seats instead of universal loose fill.
- No contact with the walls. The insert holds glass and diffusers away from the walls, so knocks and pressure go into the board, not into the product.
- Minimal play. A product that cannot move cannot hit anything.
- Separate compartments. Parts that can damage each other, such as a glass shade and a metal body, go into separate compartments.
- Ready for returns. A unit box designed so that the customer or your returns team can pack the product back safely.
Through our partners we can also supply foam inserts and honeycomb fillers. For LED modules and drivers that are sensitive to static, antistatic (ESD) corrugated board can be supplied on request; we do not declare compliance with ESD standards (see packaging for electronics and automation). A comparison of loose fill, paper and inserts is in void fill and product protection compared.
What the box has to carry: EU marking rules for lighting
A box for lighting is often also the sales pack, so the artwork has to leave room for information required by EU law. The table summarises the rules that concern packaging, as of 13 November 2026; general information, not legal advice. The content of these markings is the responsibility of the manufacturer or importer.
| Requirement | Legal basis | Applies to | What it means for the box |
|---|---|---|---|
| Energy label printed on the packaging | Delegated Regulation (EU) 2019/2015, Article 3(1)(a) and Annex III (applies from 1 September 2021) | Light sources placed on the market on their own, not in a luminaire, and in packaging | Standard label at least 36 x 75 mm; small label at least 20 x 54 mm, only on packaging less than 36 mm wide; packaging not smaller than 20 x 54 mm; monochrome only if all other print on the box is monochrome; if the label is not on the side facing the customer, that side shows an arrow with the energy class |
| Product information on the packaging | Regulation (EU) 2019/2020, Annex II, point 3(b) | Light sources in packaging displayed at a point of sale before purchase (separate control gears have their own list) | Useful luminous flux in a font at least twice as large as the power, colour temperature, beam angle and electrical interface on the side facing the buyer; further data such as lifetime, colour rendering and dimming or disposal warnings; symbols are allowed |
| Replaceability of the light source | Regulation (EU) 2019/2020, Article 4(2) | Luminaires and other containing products sold directly to end users | Information whether the light source and control gear can be replaced, on the packaging at least as a pictogram |
| Crossed-out wheeled bin symbol | Directive 2012/19/EU (WEEE), Article 14(4) and Annex IX | Electrical and electronic equipment | The symbol goes on the product; on the packaging, instructions and warranty only in exceptional cases where the size or function of the product requires it |
| CE marking | Directive 2014/35/EU (Low Voltage Directive), Article 17(1) | Equipment rated between 50 and 1000 V AC or between 75 and 1500 V DC | On the product or its data plate; on the packaging and accompanying documents only where that is not possible or not warranted |
| Identification and contact details | Directive 2014/35/EU, Articles 6(5), 6(6) and 8(3); Regulation (EU) 2019/1020, Article 4(4); Regulation (EU) 2023/988, Article 9(5) and 9(6) | Manufacturers, importers and the responsible economic operator in the EU | Type or batch number and name and postal address on the product or, where that is not possible, on the packaging or an accompanying document; the EU economic operator may also be shown on the parcel |
Two practical points. Luminaires sold with a light source inside do not carry the energy label on the box; their supplier provides information on the contained light source instead (Article 3(2) of Regulation 2019/2015). Low-voltage products such as 12 V or 24 V LED strips are outside the voltage range of the Low Voltage Directive; for consumer products the General Product Safety Regulation (EU) 2023/988 sets similar identification rules. Check your product with your compliance adviser. Transport symbols such as fragile or this way up are covered in handling marks on cartons.
Print and finish
We print by flexo in up to 4 colours or digitally, including UV. Digital print is convenient when a range has many versions, for example the same luminaire in several colour temperatures or wattages, and it can add variable data such as a serial number or a QR code. For a retail look we offer lamination with printed paper, varnish and a film window through which the lamp is visible; a window made of paper is also possible. We match colours to a Pantone reference. Differences between the methods are explained in printing on corrugated boxes. A new box can be made first as a prototype, so that you can check how the product sits inside before the run.
Courier shipping, pallets and export
For courier shipping the unit box should be close to the product with its insert, because carriers often charge by dimensional weight when it is higher than the actual weight. Long parcels such as LED tubes or floor lamp stands may fall under carriers’ rules for long or non-standard parcels, so check the conditions of your carrier before you fix the box length. If a lamp contains a battery, ask your carrier about the conditions for batteries before you choose the pack. For shipments outside the EU see export packaging.
Checklist for lighting buyers
- Product data. Dimensions and shape, including parts that stick out, weight, and which parts are glass.
- Way of packing. One piece per box, a set, or an outer carton with several pieces; who packs, by hand or on a line.
- Sales channel. Shelf, wholesale or courier shipping, and whether the same box must work for returns.
- Markings. Energy label, product information, symbols, codes and contact details: who supplies the content and the number of language versions.
- Print and finish. Number of colours, versions, window, lamination or varnish.
- Batteries and special parts. Does the product contain a battery or parts sensitive to static?
- Testing. Prototype before the run and, if needed, package tests on your product and route.
- Logistics. Pallet type, pieces per carton and destination countries.
What we can do
We are a manufacturer of corrugated packaging in Lubartów, Poland. We make unit boxes, outer cartons, inserts, dividers and lattices for lighting to your dimensions, in 3-layer board (E, B, C), 5-layer board (EB, BE, BC and heavy AC) and 7-layer AAC. We design the box and the insert together, make prototypes and can arrange package tests in a partner laboratory on terms agreed individually. We tailor order quantities to your needs – we also make short runs and prototypes. If a construction requires a minimum quantity, we state it in the quote. Most orders are delivered within 7 days (max. 16 working days); delivery to other EU countries is by arrangement.
Sources
Delegated Regulation (EU) 2019/2015 on energy labelling of light sources (Article 3, Annex III); Regulation (EU) 2019/2020 on ecodesign of light sources (Article 4, Annex II); Directive 2012/19/EU on WEEE (Article 14, Annex IX); Directive 2014/35/EU (Articles 1, 6, 8 and 17); Regulation (EU) 2019/1020 (Article 4); Regulation (EU) 2023/988 (Article 9). All checked on 13 November 2026; amendments may follow, so check the current consolidated texts.
What to send us
Send the product type, dimensions, weight, the way of packing, the print you need and, if you have one, a sample, a photo with a ruler or a drawing. We produce boxes to your dimensions. Send your enquiry through our home page.
Frequently asked questions
What is the best packaging for light bulbs?
A unit box with an insert cut to the shape of the bulb, or an outer carton with a divider lattice in which every bulb has its own cell. The glass must not touch the walls of the box or the next bulb.
How should LED tubes be packed for shipping?
Long, narrow products such as LED tubes go into rectangular tube-type boxes or telescopic boxes, and several pieces are separated by layer pads or dividers in an outer carton. We make rectangular tube-type boxes up to 240 cm inside length and telescopic boxes for many metres. Check your carrier’s conditions for long parcels before you fix the box length.
Does the energy label have to be printed on the box?
Yes, for a light source such as a bulb or an LED tube placed on the market on its own in packaging: Article 3(1)(a) of Delegated Regulation (EU) 2019/2015 requires the label to be printed on the packaging. Luminaires sold with a light source inside do not carry this label on the box; their supplier provides information on the contained light source instead. General information as of 13 November 2026, not legal advice.
How large must the energy label on the packaging be?
Under Annex III of Regulation (EU) 2019/2015 the standard label is at least 36 mm wide and 75 mm high. The small label, at least 20 mm wide and 54 mm high, may only be used on packaging less than 36 mm wide, and the packaging itself must not be smaller than 20 mm by 54 mm. If the label is not on the side facing the customer, that side must show an arrow with the energy class.
Can you make a box for a chandelier, a lampshade or a floor lamp?
Yes. Whether you call it a chandelier box, a lampshade carton or a long box for a floor lamp, we design the box and the insert around the actual product: a seat for the body, separate compartments for shades and cables, and corner pieces where parts stick out. Large luminaires can go into die-cut boxes up to 260 x 150 cm or into larger formats.
Can the box have a window and printed technical data?
Yes. We print by flexo in up to 4 colours or digitally, including UV, which suits ranges with many versions. We can add lamination with printed paper, varnish and a film window, or a window made of paper. The technical data, symbols and codes come from your artwork, and their content is your responsibility.
Do you guarantee that lamps will arrive without breakage?
No. No supplier can honestly promise that. We design the box so that the product does not move and does not touch the walls, we can make a prototype before the run, and we can arrange package tests (compression, drop, transport simulation) in a partner laboratory on terms agreed individually.
In what quantities and how quickly can you deliver?
We tailor order quantities to your needs – we also make short runs and prototypes. If a construction requires a minimum quantity, we state it in the quote. Most orders are delivered within 7 days (max. 16 working days). Delivery to other EU countries is by arrangement.