The Parcel-Locker Mailer: Designing a Die-Cut Carton for InPost A, B and C Slots in Poland
In Poland one piece of infrastructure decides how a very large share of e-commerce cartons are designed: the parcel locker. InPost alone reported 28,165 parcel machines in Poland at the end of 2025 and more than 700 million parcels handled in Poland in 2024, according to company data. Few packaging formats are so strongly dictated by a single piece of equipment, and the die-cut tape-free mailer is the carton that fits it best. It is made of one sheet, arrives flat, is assembled in seconds and can be sized to a locker slot. This guide explains how to design such a mailer for the three slot sizes A, B and C, which mistakes to avoid and what to put in an enquiry. For the general idea of the mailer see FEFCO 0427 corrugated mailers.
The three slots you design around
| Slot | Maximum parcel size in Poland | Limit |
|---|---|---|
| A | 80 x 380 x 640 mm | 25 kg |
| B | 190 x 380 x 640 mm | 25 kg |
| C | 410 x 380 x 640 mm | 25 kg |
These are the maximum dimensions published by the carrier for Polish lockers; the carrier can change them, so confirm the current specification before you order a large run. They are also not the same everywhere: for Austria InPost gives 61 x 38 x 8, 61 x 38 x 19 and 61 x 38 x 37 cm, which differs from the Polish size C. If you ship to several countries, design for the smallest common dimension or make a separate carton per country.
From product to carton: three sets of dimensions
- Inside dimensions are set by the product with its inner wrapping. Measure the product at its largest points and add room for a protective layer.
- Outside dimensions are the inside dimensions plus the board. Nominal thickness is about 1.5 mm for 3-layer flute E and 2 to 3 mm for flute B, with a tolerance of about 5%; in a mailer the walls and lid are partly double, so the closed carton is higher than inside height plus two board thicknesses. We confirm the final figure on a prototype.
- The slot is the ceiling for the outside dimensions. Leave a few millimetres of reserve: a carton that bulges or has a slightly raised lid may not enter the slot, even if the drawing says it should.
The same logic as in internal or external dimensions applies here, only with a hard limit on one side. Choosing the smallest carton that fits the product also helps the freight bill; see right-sizing boxes and dimensional weight.
Why a die-cut mailer suits lockers
- It is one piece of board, so there is no tape and no extra parts to lose.
- It is delivered flat, so it takes little space in the store.
- It can be made to the millimetre, which keeps the product from moving and keeps the height within the slot.
- The print on the lid and inside walls turns the carton into branded packaging when the customer opens it.
- A closed carton has a flat shape that slides into a slot without catching.
Styles and codes are explained in the FEFCO catalogue and in our article on die-cut and slotted cartons.
Board and strength
For light products, such as accessories, cosmetics, small electronics in their own box or clothes, 3-layer board with flute E or B is the usual choice. For heavier products, glass or items that are stacked in a delivery van, 5-layer board is safer. The weight limit of the slot is 25 kg, but the carton should be chosen for the real product weight and for the way it travels, not for the limit. How strength is estimated is explained in ECT, BCT and the McKee formula.
Typical mistakes
- Designing the carton for the product and checking the slot only afterwards.
- Forgetting the board thickness and the double walls when calculating the outside height.
- No reserve: a carton exactly at the limit may jam in a slot.
- Using one carton for every order, so that small products travel in a large box.
- Copying Polish sizes for a route to another country, where the slots differ.
- Choosing the board by the 25 kg limit instead of by the real weight and the stacking.
More on buyers’ errors is in five mistakes when choosing a box for a parcel locker.
One carton per slot, not per product
A practical way to cut cost is to standardise on three cartons that match slots A, B and C and to assign every product to the smallest one that fits. This limits the number of store items and simplifies ordering. Where you sell very different products, add a second carton in each slot size rather than a different carton for every product. For small e-commerce runs see short-run corrugated cartons and e-commerce packaging.
What to put in an enquiry
- The slot size or sizes you ship to (A, B, C) and the country.
- The dimensions and weight of the product with its inner wrapping.
- The number of different products and the run size.
- The print: one to four colours by flexo or digital print, inside and outside.
- Whether you want a prototype to check the fit in a real slot.
How to order
Send the details through our home page. We reply with a quotation within a few hours on working days and most orders leave our plant within 7 days; orders that need artwork approval, test prints, plotter samples, a new cutting die or a very complex construction take longer, up to 16 working days. We ship from Poland across Europe and can make a prototype before the run. Read the guide to buying cartons from Poland and our wholesale terms.
See also: Parcel Locker Box Sizes in Europe: Country-by-Country Cheat Sheet (November 2026)
Frequently asked questions
What are the slot sizes of InPost parcel lockers in Poland?
In Poland the maximum dimensions are 80 x 380 x 640 mm for size A, 190 x 380 x 640 mm for size B and 410 x 380 x 640 mm for size C, with a limit of 25 kg per parcel. Check the current carrier specification before you fix a size, because carriers can change it.
Is a mailer without tape allowed in a locker?
A parcel only has to fit the slot and be closed securely. A self-locking die-cut mailer of the FEFCO 0427 type closes without tape, which saves packing time; whether you add a label or a seal strip is your decision.
Do I design for the inside or the outside of the carton?
Both. The product decides the inside dimensions, the slot decides the maximum outside dimensions, and the board thickness is the difference between them. Always check the closed carton against the slot on a prototype.
Are slot sizes the same in other countries?
No. For example, for Austria InPost publishes sizes of 61 x 38 x 8, 61 x 38 x 19 and 61 x 38 x 37 cm. Other carriers have their own lockers and limits, so check the specification for every route you ship on.
What board should I choose for a locker mailer?
Light products usually go in 3-layer board with flute E or B, and heavier ones in 5-layer. The weight limit is 25 kg, but the carton should be chosen for the real weight and the route, not for the limit.
Can you make a short run or a prototype?
Yes. We make prototypes before the run and runs of any size, flexo print in up to four colours or digital print. We quote within a few hours on working days and most orders leave our plant within 7 days (max. 16 working days).