Packaging for Filters, Seals and Fittings: Unit Boxes, Outer Cartons and Inserts for Small Series Parts
Packaging for filters, seals and fittings is usually a two-level system: a printed unit box of 3-layer E- or B-flute corrugated board for each filter, gasket, hinge or pack of screws, and an outer carton with dividers that carries the unit boxes to the warehouse or the shop. The design starts from the weight and sensitivity of the part: seals should lie without tension and away from light, filters need the orientation their maker specifies, and dense fasteners need a carton that is not overloaded. We make both levels to your dimensions.
Typical products, risks and packaging
Filters, seals and fittings are small series products sold in many versions, so the box protects the part, says what is inside and often sells it on the shelf. The table gives typical starting points; the final construction depends on your product and route. For automotive parts in general see packaging for automotive parts.
| Product | Main risk in transport and storage | Unit pack | Outer pack |
|---|---|---|---|
| Panel and cabin air filters | Crushed pleats or frame, damaged seal, wrong orientation | Close-fitting die-cut box, insert that keeps the load off the filter media | Carton with dividers and the orientation marks the filter maker specifies |
| Oil, fuel and cartridge filters | Dented housings, damaged threads and seals, weight concentrated in a small volume | Printed box with part number and application data | Carton with a lattice so filters do not knock together |
| Flat gaskets | Bending and creasing, deformation in the stack | Flat box, with or without a window | Carton with layer pads so gaskets lie flat |
| O-rings and moulded seals | Tension and compression, light (especially UV), contact with certain metals | Box without a window or with an opaque inner bag; no hanging | Carton with dividers; batch or date on each unit box |
| Furniture and building fittings (hinges, handles) | Scratched finished surfaces, parts rubbing, weight | Box with a lid or set box with an insert that separates parts | Multi-pack carton with dividers, stiffer board |
| Fasteners (screws, bolts, anchors) | High weight in a small volume, burst corners, wrong size picked | Small box printed with size and type | Outer carton of unit boxes, 5-layer board where needed |
| Kits of mixed parts | Parts mixing or missing, seals touching metal | Set box with a board insert and a separate compartment or bag for seals | Outer carton sized to the set box |
Choosing the board
For light unit boxes (gaskets, O-rings, small filters) we usually use 3-layer board with E flute, about 1.5 mm thick, whose smooth surface takes print well. For heavier parts, such as fittings or larger filters, B flute (2 to 3 mm) is the usual step up, and outer cartons can be made of 5-layer board. On our suppliers’ datasheets, nominal ECT is 3 to 5.5 kN/m for 3-layer E and 3 to 6 kN/m for 3-layer B. Our full range: 3-layer E, B and C; 5-layer EB, BE, BC and heavy AC; 7-layer AAC.
With small metal parts the weight per carton matters more than the size. A small carton of screws or hinges is heavy for its volume, and the load sits on the bottom and the corners. Agree the maximum gross weight per outer carton with your warehouse and customers, then choose the board for that weight and the stacking height. Often a smaller carton with fewer unit boxes works better than one large, heavy carton.
Seals and gaskets: what storage guidelines mean for the box
Rubber products can change their properties in storage when exposed to heat, light, ozone, oxygen and humidity, and they can also be damaged by deformation. ISO 2230 (Rubber products – Guidelines for storage, third edition 2026) and seal makers’ storage guidelines therefore treat packaging as part of storage control. For the box this means:
- No tension or compression. Seals should be stored free from stretching, squeezing or other deformation, and O-rings should not be hung. Choose a flat box or one deep enough that the seal is not bent to fit, and do not plan hook display for loose rings.
- Protection from light. The guidelines ask for protection from direct sunlight and strong artificial light with a UV content. A film window shows the seal but lets light in; for stock that stays long in the warehouse, consider an opaque inner bag, a printed picture instead of a window, or a paper window.
- Suitable materials in contact. One seal maker’s handbook advises against PVC or other film containing plasticiser in direct contact with rubber and names opaque materials such as PE film or PE-coated kraft paper. Ask your seal supplier which materials may touch the product and tell us before the window film or the bag is chosen.
- No contact with certain metals. Copper and manganese and their alloys can harm some rubbers, so in kits keep seals in their own compartment or bag, away from metal fittings.
- Stock rotation. Storage guidelines expect first in, first out. Leave a field on each unit box for the batch number or production date, or print it digitally.
Temperature and humidity limits differ between guidelines and depend on the rubber type, so take them from your seal maker. A corrugated box is not a moisture barrier: where the guideline or your customer asks for sealed or moisture-proof packaging, add an inner bag.
Filters: orientation, stacking and opening
Filter makers’ handling instructions depend on the filter type. One maker of panel filters asks for them to be carried vertically, kept this side up, stored in a clean and dry place, not stacked and not opened with a cutter. Another asks for carbon filters to be stored flat and particulate filters upright, in both cases in their original packaging. What this means for the packaging:
- Orientation marks that match the instruction. Print “this way up” or “store flat” only as the filter maker specifies, and keep the symbols consistent with ISO 780; see handling marks on cartons. A symbol does not protect the filter by itself, so the box should also stand stable in the intended position.
- Load off the media. An insert or a close fit carries the load through the frame or housing, not through the pleats or the gasket. Where the maker says “do not stack”, either the outer carton and the pallet pattern carry the load above, or the filters travel unstacked; tell us which applies.
- Opening without a blade. A perforated opening or a flap design that needs no knife helps where instructions forbid cutting the box open.
- Dry storage. Board absorbs moisture, so keep filter boxes dry in storage and on the route.
Fittings and fasteners: weight, sets and corrosion
Hinges, handles, brackets and screws are dense, so a carton fills up by weight before it fills by volume. Finished surfaces (painted, chromed or anodised) should not rub against each other, and in sets every part needs a fixed place so that nothing is missing at assembly.
- Set boxes with inserts. A board insert divides the box and holds each part in place; give us the list of parts and their dimensions and we design the layout.
- Dividers in outer cartons. Dividers or lattices keep unit boxes upright and apart and make picking easier.
- Corrosion. Board does not protect metal against corrosion. If parts are prone to rust, agree the protection with your quality team, for example a film bag or liner inside the carton, which we can supply with the packaging through a partner; see packaging for humidity, cold, corrosion and sensitive loads.
Print, codes and the information the box must carry
The box of a small part often has to do the work of a product label. We print flexo in up to four colours or digitally (UV); digital printing allows variable data such as part numbers, application data, batch numbers or a QR code on each box without new plates. For print technologies and varnishes see printing on corrugated boxes.
Barcodes follow GS1 rules. Consumer units sold at a till normally carry an EAN-13 barcode with a GTIN-13. Outer cartons that do not cross a retail point of sale carry their own number, a GTIN-14, in an ITF-14 barcode, or in a GS1-128 barcode where extra data such as a batch number or a date is needed. The brand owner allocates the numbers through its GS1 member organisation; we print the codes you supply.
For products intended for consumers, the General Product Safety Regulation (EU) 2023/988, which has applied since 13 December 2024, requires certain data on the product or, where its size or nature does not allow it, on the packaging or in an accompanying document: a type, batch or serial number (Article 9(5)), the manufacturer’s name, registered trade name or trade mark and postal and electronic address (Article 9(6)) and, for imported products, the same details of the importer (Article 11(3)). Instructions and safety information must be in a language consumers easily understand, as determined by the Member State, unless the product can be used safely without them (Article 9(7)). Where specific Union rules regulate the safety of a product, the GPSR covers only what they do not (Article 2(1)). A seal or a screw seldom has room for markings, so reserve space for these data on the box. Status 13 November 2026; general information, not legal advice.
Shop display and e-commerce
Parts sold on hooks need a hang tab or a hanging hole; its design depends on the weight of the product, so give it in the enquiry. For parts sent to online customers, either the unit box is strong enough to travel in a courier parcel on its own or it goes into a shipping carton; tell us which, because the board and the closure differ.
Under Article 24 of the PPWR (Regulation (EU) 2025/40), from 1 January 2030 at the earliest, whoever fills grouped, transport or e-commerce packaging must keep the empty space ratio at no more than 50%, and filling material counts as empty space. The calculation method, due by 12 February 2028, is to take into account small products that can be damaged by larger ones. For a unit box, which is sales packaging, empty space must be reduced to the minimum needed for its function, including product protection, by the same date. For small parts, an outer carton sized to the unit boxes is the main lever. See the PPWR checklist for packaging buyers. Status 13 November 2026; general information, not legal advice.
Export
For long routes, sea freight and storage abroad see corrugated export packaging. ISPM 15 regulates wood packaging material in international trade, such as wooden pallets, crates and dunnage, so check the wooden parts of the shipment against the destination’s rules; see ISPM 15 and corrugated packaging.
Checklist: what to settle with your packaging supplier
- Product data: dimensions, weight, units per box and per outer carton, photos or a sample.
- Sensitivity: the seal maker’s storage instructions (light, deformation, materials in contact), the filter maker’s orientation and stacking instructions, finished surfaces of fittings.
- Sales channel: shelf, hook, online parcel or industrial customer, and whether the unit box must survive a courier parcel on its own.
- Window: film, paper or none, and which film may touch the product.
- Print and data: number of versions, part numbers, GS1 barcodes, a batch or date field, manufacturer and importer details under the GPSR, languages.
- Outer carton: maximum gross weight, dividers, stacking height, pallet pattern, orientation marks.
- Corrosion and moisture: storage time and conditions, and whether a bag, liner or corrosion protection is needed.
- Testing: a prototype with your product and, if your customers require it, a package test (compression, drop, transport simulation).
What we can do
We design and produce unit boxes, set boxes, outer cartons, inserts, dividers and lattices to your dimensions, in 3-layer E, B and C, 5-layer EB, BE, BC and heavy AC, and 7-layer AAC board. We print flexo in up to four colours or digitally (UV) with variable data, match Pantone colours, and can add a film window or, made to order, a paper window, hang tabs or hanging holes, perforated openings, varnish or litho-lamination. Foam inserts and film bags or liners can be supplied with the packaging through partners. We make a prototype before the run; package tests (compression, drop, transport simulation) can be arranged in a partner laboratory, with terms agreed individually, and we can trial cartons on your packing line. We can also review your box sizes and propose where a product family can share a few base sizes, with differences in the insert and the print. We tailor order quantities to your needs – we also make short runs and prototypes. If a construction requires a minimum quantity, we state it in the quote. Most of our orders are delivered within 7 days (max. 16 working days). Delivery within the EU is by arrangement; we already supply business customers in Lithuania, Germany, Slovakia, Czechia and the Netherlands.
Sources
Regulation (EU) 2023/988 on general product safety on EUR-Lex (Articles 2, 3, 9, 11 and 52); Regulation (EU) 2025/40 on EUR-Lex (Article 24); ISO, ISO 2230:2026 Rubber products – Guidelines for storage; GS1 New Zealand, bar coding basic user guide; storage and handling instructions published by seal and filter manufacturers. Check the current texts before you decide: we did not find the PPWR implementing acts on the empty space ratio in EUR-Lex on 13 November 2026.
What to send us
Send the product’s dimensions and weight, photos or a sample, the number of units per box and per outer carton, the sales channel, the print and the number of versions, and any storage or handling instructions from your seal or filter maker. We produce boxes to your dimensions and propose the board and construction in the quote. Send your enquiry through our home page.
Frequently asked questions
What board is used for boxes for filters, gaskets and fittings?
For light unit boxes, such as gaskets, O-rings and small filters, we usually use 3-layer board with E flute, about 1.5 mm thick, which has a smooth surface for print. Heavier parts, such as fittings or larger filters, usually need B flute (2 to 3 mm), and outer cartons can be made of 5-layer board. We choose the board from the weight per box and per outer carton and from the stacking height.
Can a box for seals have a window?
Yes, we can make a film window or, made to order, a paper window. Storage guidelines for rubber products ask for protection from direct sunlight and strong artificial light with a UV content, so for seals that stay long in stock consider an opaque inner bag, a printed picture instead of a window, or a paper window. Ask your seal supplier which materials may touch the seal: one seal maker advises against PVC or other plasticised film in direct contact with rubber.
Can you print a different part number on every box?
Yes. Digital printing, including UV, allows variable data such as part numbers, application data, batch numbers or a QR code on each box without new printing plates. For large runs of one version, flexo printing in up to four colours is the usual choice.
What must the packaging of a consumer part show under the GPSR?
Under Regulation (EU) 2023/988, which has applied since 13 December 2024, the product must carry a type, batch or serial number and the manufacturer’s name and postal and electronic address, and for imported products also the importer’s details. Where the size or nature of the product does not allow this, the data go on the packaging or in an accompanying document (Articles 9(5), 9(6) and 11(3)). This is general information, not legal advice.
How should filter boxes be marked for orientation?
Follow the filter maker’s handling instruction, because it differs between filter types: some filters must be carried and stored upright, others flat. Print the matching handling symbols, keep them consistent with ISO 780, and make sure the box is stable in the intended position. A symbol does not protect the filter by itself.
Can you pack mixed kits of fittings and seals in one box?
Yes. We make set boxes with a board insert that gives each part its own place. Seal makers advise keeping rubber seals away from certain metals, such as copper and manganese, so in kits we plan a separate compartment or bag for the seals. Send us the list of parts and their dimensions.
Do the PPWR empty-space rules apply to outer cartons of small parts?
Yes, from 1 January 2030 at the earliest. Article 24 of Regulation (EU) 2025/40 sets a maximum empty space ratio of 50% for grouped, transport and e-commerce packaging, and filling material counts as empty space. The calculation method, due by 12 February 2028, is to take into account small products that can be damaged by larger ones. Status 13 November 2026; general information, not legal advice.
Do you make prototypes, and is there a minimum order?
Yes, we make a prototype before the run so you can check it with your product. We tailor order quantities to your needs – we also make short runs and prototypes. If a construction requires a minimum quantity, we state it in the quote.