Corrugated Packaging for Castings and Metal Parts: Heavy-Duty Cartons and Pallet Boxes Instead of Crates
Corrugated packaging for castings and metal parts means cartons, crates and pallet boxes of 5-layer and 7-layer board and heavy AC and AAC board, which replace wooden crates for heavy products of small volume. We make them to size, also for long steel parts. Castings, forgings, sections and machined parts are heavy and have edges that can damage an ordinary carton, so we start choosing the board and the construction from the weight of a piece, its shape and the way it is laid in the pack. We prepare a quotation within a few hours on working days and most orders leave our plant within 7 days (max. 16 working days).
What heavy-part packaging is made of
The base is 5-layer and 7-layer board. For the greatest weights we use heavy AC (5-layer) and AAC (7-layer) board, whose thickness reaches 8.5 to 8.9 mm for AC and 12.6 to 13.5 mm for AAC; see our article on AC and AAC board. Bases are reinforced with extra layers, and the construction is joined by metal stapling or multi-point gluing. The inside is organised with inserts, layer pads and grids made of board in any size, so parts do not touch each other or shift in the pack.
Problem, solution and data for a quotation
| Problem | Solution | What to give for a quotation |
|---|---|---|
| High weight in a small pack | 5-layer or 7-layer board, heavy AC or AAC, reinforced base | Weight of one piece and of the set, outer dimensions |
| Sharp edges and protruding parts | Cut inserts, dividers, extra layers at points of contact | Photo or drawing of the product, points of contact with the pack |
| Many pieces one on top of another | Layer pads and grids between layers | Number of layers, pieces per layer |
| Long sections and bars | XXL packs, formats up to 10 x 3 m | Length and section, weight, way of support |
| A whole pallet of small parts | Pallet box or octabin | Dimensions and weight of the load, stacking |
| Moisture and corrosion | Solutions agreed in the enquiry | Transport and storage conditions, storage time |
Typical pack layouts
- Carton with cavities: a cut insert follows the shape of the product, so each piece has its own place.
- Crate with a reinforced base: heavy parts laid in layers and separated by layer pads.
- Pallet box with inserts: many smaller parts in one pack on a pallet.
- Longitudinal pack: long sections and bars supported at several points.
The board version is lighter than a wooden crate with the same function and can be delivered flat. For shipments abroad see also corrugated export packaging.
Where this packaging is used
We make packaging for metal products for companies that send parts for further processing, to assembly or to the final receiver. The most common cases:
- Castings and forgings sent for further machining.
- Steel parts after machining.
- Machine parts, bodies and metal housings.
- Structural elements and fittings sent loose or in layers.
- Long sections, bars and tubes in longitudinal packs.
- Outer packs with several products on one pallet.
For automotive parts see packaging for automotive parts.
Pallet boxes and octabins instead of crates
When there are many products and each weighs little, a whole-pallet pack is often the right choice. We make pallet boxes of 5-layer and 7-layer board and octabins, see corrugated pallet packaging. We do palletising and pallet boxes in house, so the load can be planned together with the pack. A pallet box can be divided into sections with dividers if different parts go into one pack or you want to keep them apart.
With such a solution it matters how the receiver will empty the pack: from the top, from the side, with a forklift or by hand. Write this in the enquiry, because the construction of the walls and the cut-outs depend on it.
Selection tips
- Edge protection. Sharp parts can cut through board when shaken. At points of contact we use extra layers and corners; describe the sharp edges of the product in the enquiry.
- Corrosion. Board absorbs moisture and is not waterproof. If parts are prone to corrosion or are shipped by sea, read packaging for humidity, cold, corrosion and sensitive loads and give the transport conditions.
- Layered stacking. Layer pads spread weight and separate parts, so plan them from the start.
- Handling and stacking. A pack with a heavy content must be comfortable to carry: handles or cut-outs in the right places help manual work. Also say how many layers of packs will be stacked on a pallet.
- Prototype. Before the run we can make a sample and check it with your product.
- Markings. We print the data you give us (flexo up to four colours or digital), for example the product number, a symbol or a “this side up” mark.
What to put in an enquiry
- The weight of one piece and of the pack with its contents.
- The dimensions of the product and the number of pieces in the pack.
- The shape, sharp edges and protruding parts.
- The way of laying: loose, in layers, in cavities.
- Transport and storage conditions, including moisture and corrosion.
- The stacking height on a pallet.
- The required markings and print data.
How to order
Send the details through our home page. We reply with a quotation within a few hours on working days and most orders leave our plant within 7 days; orders that need artwork approval, test prints, plotter samples, a new cutting die or a very complex construction take longer, up to 16 working days. We ship from Poland across Europe and can make a prototype before the run. Read the guide to buying cartons from Poland and our wholesale terms.
See also: Packaging for Bearings and Machine Parts: Corrugated Cartons, Inserts and What to Specify
See also: Packaging for Cutting Tools: Corrugated Boxes and Inserts for Drills, Milling Cutters and Blades
Frequently asked questions
Can board replace a wooden crate for heavy castings?
Often yes, especially with 7-layer and heavy AC or AAC board with a reinforced base. The final choice depends on the weight, shape and way of transport that you give in the enquiry, and any doubts are checked on a prototype.
What board suits steel parts?
For heavier products we use 5-layer and 7-layer board and, for the greatest weights, heavy AC (5-layer) or AAC (7-layer). We choose it from the weight of a piece, the layout in the pack and the stacking.
How do you protect the sharp edges of castings?
We use cut inserts, dividers and extra layers of board at the points of contact. A photo or drawing of the product with the edges marked helps.
Can you make a pack for long metal parts?
Yes, we make longitudinal packs and large formats up to 10 x 3 m. Give the length, section and weight of the parts and the way they are supported.
Does board protect parts against corrosion?
Board alone does not protect against corrosion and is not waterproof. If it matters, describe the transport and storage conditions and we will propose a solution from our range of packaging for humidity and corrosion.
Will you make a prototype before the run?
Yes, prototypes can be made before the run. They let you check the fit to the product, the layered layout and how comfortable the pack is to carry.